Gardner Denver 9CDL R Series Parts List Operating And Service Manual Download Page 6

Page: 6 / 52

37-1-615 Page 5

LIST OF ILLUSTRATIONS

FIGURE 2-1

– OPERATING PRINCIPLE.............................................................................................................................. 10

FIGURE 2-2

– ACCESSORIES AND SAFETY DEVICES ..................................................................................................... 11

FIGURE 2-3 - BELT DRIVE OVERHUNG LOAD CALCULATIONS ...................................................................................... 14
FIGURE 2-4

– OUTLINE DIMENSIONS ............................................................................................................................... 17

FIGURE 2-5

– OUTLINE DIMENSIONS (CONTINUED) ....................................................................................................... 18

FIGURE 3-1

– MAXIMUM RATING ....................................................................................................................................... 19

FIGURE 3-2

– WATER QUALITY REQUIREMENTS ............................................................................................................ 20

FIGURE 3-3

– LIQUID RATE ................................................................................................................................................ 21

FIGURE 3-4

– INLET WATER INJECTION DIAGRAM .......................................................................................................... 21

FIGURE 3-5

– ALTITUDE – PRESSURE/VACUUM ............................................................................................................. 22

FIGURE 3-6

– MINIMUM SPEED, MAXIMUM PRESSURE OR VACUUM ........................................................................... 23

FIGURE 4-1

– AEON PD SYNTHETIC LUBRICANT ........................................................................................................... 25

FIGURE 4-2

– SYNTHETIC LUBRICANT CHART ............................................................................................................... 26

FIGURE 4-3

– NON-SYNTHETIC LUBRICANT CHART ....................................................................................................... 26

FIGURE 4-4

– OIL BATH FILTER ......................................................................................................................................... 28

FIGURE 4-5

– OIL WETTED FILTER-SILENCER ................................................................................................................ 28

FIGURE 4-6

– DRY TYPE FILTER AND FILTER-SILENCER ............................................................................................... 29

FIGURE 6-1

– ADAPTOR PLATE .......................................................................................................................................... 35

FIGURE 6-2

– ADAPTOR PLATE .......................................................................................................................................... 35

FIGURE 6-3

– SPANNER WRENCH ...................................................................................................................................... 35

FIGURE 6-4

– ADAPTOR PLATES ....................................................................................................................................... 35

FIGURE 6-5 - PULLER .......................................................................................................................................................... 36

IGURE 6-6 - ALTERNATE ADAPTOR PLATES .................................................................................................................. 36

FIGURE 6-7 - CARRIER FLANGE ......................................................................................................................................... 37
FIGURE 6-8 - BEARING CLAMP PLATE SHIM ..................................................................................................................... 37
FIGURE 6-9 - PULLER .......................................................................................................................................................... 37
FIGURE 6-10 - ROTOR SLING REMOVAL ........................................................................................................................... 39
FIGURE 6-11 - JACK SCREWS ............................................................................................................................................ 39

FIGURE 7-1

– ROTOR SHAFT SEALS ................................................................................................................................ 40

FIGURE 7-2

– BEARING SPACERS .................................................................................................................................... 40

FIGURE 7-3

– DISCHARGE OPENING ................................................................................................................................ 40

FIGURE 7-4

– LOWER THE GATE ROTOR INTO THE HOUSING ASSEMBLY .................................................................. 40

FIGURE 7-5

– ANGULAR CONTACT BEARING ASSEMBLY .............................................................................................. 41

FIGURE 7-6

– BEARING INSTALLATION ........................................................................................................................... 41

FIGURE 7-7

– DISCHARGE END BEARING CARRIER ....................................................................................................... 42

FIGURE 7-8

– ROTOR END CLEARNACE CHART (UNIT COLD) ....................................................................................... 42

FIGURE 7-9

– DEPTH MICROMETER - ROTOR LOBES .................................................................................................... 42

FIGURE 7-10

– OUTSIDE MICROMETER - THICKNESS OF SHIMS .................................................................................. 42

FIGURE 7-11

– DISCHARGE OPENING & DOWEL PINS ................................................................................................... 43

FIGURE 7-12

– DIAL INDICATOR ........................................................................................................................................ 43

FIGURE 7-13

– SEAL INSTALLATION GUIDE ..................................................................................................................... 44

FIGURE 7-14

– PROTECTIVE INSTALLATION SLEEVES OVER EACH SHAFT ................................................................ 44

FIGURE 7-15

– MICROMETER - THICKNESS OF SHAFT SHIM SET ................................................................................ 45

FIGURE 7-16

– SHAFT EXTENTION ................................................................................................................................... 45

FIGURE 7-17

– BEARING PRESS PLATES ......................................................................................................................... 46

FIGURE 7-18

– BEARING CLAMP PLATES ........................................................................................................................ 46

FIGURE 7-19

– DISCHARGE OPENING .............................................................................................................................. 46

FIGURE 7-20

– REINFORCING PLATE ............................................................................................................................... 46

FIGURE 7-21

– END COVER ASSEMBLY ........................................................................................................................... 47

FIGURE 7-22

– BEARING BORE ......................................................................................................................................... 48

FIGURE 7-23

– DEPTH MICROMETER - MEASURE DISTANCE TO END OF BEARING SPACER ASSEMBLY ............... 48

FIGURE 7-24

– OIL SEAL ON GATE ROTOR SHAFT ASSEMBLY ..................................................................................... 48

FIGURE 7-25

– SLIDE SHIMS OVER THE SHAFTS ASSEMBLY ........................................................................................ 48

FIGURE 7-26

– PRESS PLATE AND JACK SCREW ASSEMBLY ....................................................................................... 49

FIGURE 7-27

– INSTALL HUB & PINION PULL TIGHT WITH LOCKING DEVICE ASSEMBLY .......................................... 49

FIGURE 7-28

– MOUNT INDICATOR AND BUTTON BRACKET ASSEMBLY ..................................................................... 49