background image

23

ECONOM MOTOR LIMIT SWITCH ADJUSTMENT 

SETTING ‘TOP LIMIT’
Once the bottom limit has been set, press and hold the up 
button on the rollixo control panel/test lead if the door stops 
on its own before reaching the desired open position, turn the 
appropriate limit screw in the positive direction, 1 complete 
turn of the switch equates to approx. 12mm of travel. This 
must be verified and large numbers of turns at a time are not 
recommended. Press and hold the up button to check motor 
position and repeat process if necessary.
If the motor does not stop within 6 inches of the desired open 
position stop the operation, press the down button to bring the 
motor approx. 12 inches below the desired stop position turn 
the appropriate open limit screw to the negative position, press 
the up button again and repeat as necessary until the door does 
stop at least 6 inches below the desired stop position. Once this 
has happened turn the appropriate limit screw to the positive 
and press and hold the up button, repeat as necessary until you 
have reached the desired up/open position. 

+

-

+

-

Adjust the 
limit switch as 
necessary until 
the desired 
end position is 
achieved.

CONNECT THE CURTAIN TO THE 
MOTOR BARREL

1) Loosen the sliding lock clips.
2) Remove the connecting pin that is pre-
installed within the ring.
3) Aligning the locking strap with the lock ring 
hole and insert the connecting pin.

4) Secure the sliding 
lock clips against the 
connecting pin.

Secure with the connecting pin provided.

Align the locking strap with the lock ring hole.

1

2

3

3

3

4

IMPORTANT: at the top limit position the bottom lath should 

be completely within the guide.

Summary of Contents for ThermaRoll 77

































Reviews: