background image

3

WHO SHOULD  

INSTALL THIS DOOR?

A minimum of two 
people must be 
available for fitting. 
GDS recommend that 
fitting and/or repair of 
garage doors be performed by a qualified, 
factory trained garage door specialist.

•  Your safety, your end user’s safety and that of the general public is our primary concern. Please 

read, understand and follow our advice. 

•  These installation instructions are intended for qualified and trained installation engineers. 

•  Installation, initial operation, servicing, repairs and dismantling of this product should only be 

carried out by a qualified and trained installation engineer.

Failure to comply with these instructions 
invalidates the warranty.
Before you begin the fitting of the door, read 
and fully understand all of the instructions 
thoroughly.

These doors meet all relevant safety 
requirements when installed according to these 
fitting instructions.
Both one and two car doors are installed in the 
same manner.
Damage to the garage door due to improper 
handling, installation or improper adjustment 
of the electric operator is not covered by 
Garage Door Systems’ warranty.

Be sure all warning labels and tags are 
properly affixed to the door and that the 
home owner is familiar with the door 
operation.
Before removing the old door or 
unpacking the door, confirm the opening 
dimensions to ensure door will fit.

!

!

!

!

IMPORTANT INFORMATION  

WARNINGS & SAFETY OBLIGATIONS

WARNING!

GENERAL NOTES

Goggles
Safety Shoes
Gloves

SAFETY EQUIPMENT

Summary of Contents for ThermaRoll 77

































Reviews: