manualshive.com logo in svg

Garage Door Systems ThermaRoll 77, Installation Instructions Manual, Page: 25 / 32

Share
Download
Garage Door Systems ThermaRoll 77 Installation Instructions Manual Download Page 25

25

25

SOMFY ROLLIXO QUICK COMMISSIONING

Page 9

Activating/Deactivating the alarm

To activate/deactivate the alarm, simultaneously press the STOP and buttons
on the receiver until the 4 indicator lights flash rapidly.
The alarm emits a beep if it has been activated.

Alarm operation

The alarm is triggered for 2 minutes if the door is raised manually.
No movement of the door is possible when the alarm is sounding.
When the alarm sounds, press a button on a remote control memorised in the receiver to stop 
it. The alarm can only be stopped with a memorised remote control.

Alarm operation test

Press buttons 

STOP

 and   on the receiver 

simultaneously.
The alarm triggers briefl y to indicate 
that it is activated.

+

Locking out the Panel

3

4

2

1

Prog

STOP

3

4

2

1

Prog

STOP

 Press buttons 

Prog

STOP

 and 

Prog

STOP

on the receiver until all the indicator lights flash.

  Entry into programming mode by pressing button 

Prog

STOP

on the receiver is locked.

Entry into motor end limit setting mode via pressing buttons 

and 

on the receiver is 

locked.

The parameter setting of the operating modes is locked, the reverse process aspplies  to 
UNlock the panel

Failure to do so will enable consumer to operate programming mode, this is potentially 
dangerous.

3

4

2

1

Prog

STOP

3

4

2

1

Prog

STOP

3

4

2

1

Prog

STOP

3

4

2

1

Prog

STOP

Rollixo Quick GuideHW_A5_02.indd   9

12-07-17   14:02

 simultaneously on the control panel until all the indicator lights flash. 

Alarm operation

The alarm is triggered for 2 minutes if the bottom rubber seal is compressed when the 

door is at its closed position. No movement of the door is possible when the alarm is 

sounding. When the alarm sounds, press a button on a remote control memorised in the 

receiver to stop it. The alarm can only be stopped with a memorised remote control.

The alarm function is factory set to activated. To activate/deactivate the alarm, simultaneously 

press the STOP and down buttons on the control panel until  the 4 indicator  

lights flash rapidly. The alarm emits a beep if it has been activated.

Alarm operation test 

Keygo transmitter required. With the 

door closed compress the bottom rubber 

seal. The alarm will sound, use pre-

programmed button on handset to turn 

alarm sounder off. If the alarm doesn’t 

sound it has been de-activated. Reactivate 

using stop and down buttons as above.

The parameter setting of the operating modes is locked, the reverse process applies  to 

UNlock the panel - ie hold/stop programme.

Summary of Contents for ThermaRoll 77

































Reviews:

No comments