16
SOMFY ROLLIXO QUICK COMMISSIONING
Page 4
This quick guide provides basic installation and commissioning guidance based on the Somfy
Rollixo RTS controller and safety edge solutions. Refer to the main Rollixo RTS controller and
safety edge installation guides where more in-depth information relating to the installation
procedure of the Rollixo RTS system is required.
Rollixo RTS Safety Edge Solutions
There is one Somfy hardwired safety edge solution available with the Rollixo RTS:
Rollixo RTS OSE - OSE stands for ‘Optical Safety Edge’.
This is supplied with a safety edge via a hard wired spiral cable and is connected to a Somfy
optical safety edge system. The optical safety edge consists of two optical cells mounted at
each end of a rubber profile. The cells project an optical beam through a hollow section of
the profile, it becomes obscured once the rubber profile is depressed. This in turn results in a
signal from the safety edge, indicating that an obstacle has been detected.
Aditional steps must be taken to ensure the straight edge of the door meets with the straight
edge of a floor extending into the guides. Failure to do so will result in; air + light gaps, false
activations of the edge etc.
Rollixo RTS Solutions
“Please refer to the Installer Guide
provided with every Rollixo, here
you will find the basic principles and
operating parameters for any CE
compliant safety edge system”
L1
L2
N
M
1
2
3
4
Bleu
Marro
n
Noir
Green/
Yellow
Brown
Blue
Black
L1
L2
N
M
1
2
3
4
Bleu
Marro
n
Noir
Sec
Safety Edge
Stop
K
5
6
7
8
9
1
Green/
Yellow
Brown
Blue
Black
Sec
Safety Edge
Stop
K
5
6
7
8
9
1
Somfy motor wiring
Connect the motor wires into terminals 1, 2, 3
& 4 as illustrated above.
Note: The motor direction can be reversed during
the commissioning procedure.
Secure the motor supply
cable in place with the
cable clamp.
✓
✗
Rollixo Quick GuideHW_A5_02.indd 4
12-07-17 14:02
Additional steps must be taken to ensure the straight edge of the door meets with the straight edge
of a floor extending into the guides, especially when removing posts - holes must be filled level with
the floor. Failure to do so will result in; air + light gaps, false activations of the safety edge etc.
Page 4
This quick guide provides basic installation and commissioning guidance based on the Somfy
Rollixo RTS controller and safety edge solutions. Refer to the main Rollixo RTS controller and
safety edge installation guides where more in-depth information relating to the installation
procedure of the Rollixo RTS system is required.
Rollixo RTS Safety Edge Solutions
There is one Somfy hardwired safety edge solution available with the Rollixo RTS:
Rollixo RTS OSE - OSE stands for ‘Optical Safety Edge’.
This is supplied with a safety edge via a hard wired spiral cable and is connected to a Somfy
optical safety edge system. The optical safety edge consists of two optical cells mounted at
each end of a rubber profile. The cells project an optical beam through a hollow section of
the profile, it becomes obscured once the rubber profile is depressed. This in turn results in a
signal from the safety edge, indicating that an obstacle has been detected.
Aditional steps must be taken to ensure the straight edge of the door meets with the straight
edge of a floor extending into the guides. Failure to do so will result in; air + light gaps, false
activations of the edge etc.
Rollixo RTS Solutions
“Please refer to the Installer Guide
provided with every Rollixo, here
you will find the basic principles and
operating parameters for any CE
compliant safety edge system”
L1
L2
N
M
1
2
3
4
Bleu
Marro
n
Noir
Green/
Yellow
Brown
Blue
Black
L1
L2
N
M
1
2
3
4
Bleu
Marro
n
Noir
Sec
Safety Edge
Stop
K
5
6
7
8
9
1
Green/
Yellow
Brown
Blue
Black
Sec
Safety Edge
Stop
K
5
6
7
8
9
1
Somfy motor wiring
Connect the motor wires into terminals 1, 2, 3
& 4 as illustrated above.
Note: The motor direction can be reversed during
the commissioning procedure.
Secure the motor supply
cable in place with the
cable clamp.
✓
✗
Rollixo Quick GuideHW_A5_02.indd 4
12-07-17 14:02