Galeo PC78MR-6 Operation & Maintenance Manual Download | Manualshive

Page: 97 / 295

background image

.

OPERATION

DETAILED CONTROLS AND GAUGES

Air Conditioner Switch

Switch (5) is used to switch the air conditioner functions ON/OFF.

Off Switch

Switch (6) is used to stop operation of the fan.

Defroster Selector Lever

Switch (7) is used to remove the mist from the front glass during
cold or rainy weather.
Selector lever to front: To defroster (open)
Selector lever to rear: Closed
The defroster can be used when the vent selector switch is set
to send air to the face or to the face and the feet.

Use Air Conditioner with Care

Ventilation

If you smoke when the air conditioner is on, the smoke may start to hurt your eyes, so open the window and turn
the lever to FRESH for a while to remove the smoke while continuing the cooling.

When running the air conditioner for a long time, turn the lever to the FRESH position once an hour to carry out
ventilation and cooling.

Temperature Control

When the air conditioner is on, set the temperature so that it feels slightly cool when entering the cab (5 to 6

°

C

(41 to 42.8

°

F) lower than the outside temperature). This temperature difference is considered to be the most

suitable for your health, so always be careful to adjust the temperature properly.

3 - 42

«
...
95
96
97
98
99
...
»

Summary of Contents for PC78MR-6








































































































































































































































































































Reviews:

No comments

Related manuals for PC78MR-6

Brand: Hyundai Pages: 168

Brand: New Holland Pages: 41

Atlas RA350LCSR

Brand: Rail-Ability Pages: 71

Brand: P.Lindberg Pages: 123

Brand: Komatsu Pages: 376

MFS YORK STORMOR M-700

Brand: Global Industrial Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands