background image

 

© 2012 G Force Automatic Gates All Rights Reserved 

GENERAL 

G-Force Automatic Gate products are covered by the manufacturer’s warranty which covers defects in materials and workmanship for 
the Warranty Periods stated below. This warranty is additional to any applicable statutory requirements, subject to the exclusions and 
limitations stated below. 

Product is deemed to be warranted from the date of initial purchase from G-Force Automatic Gates. Proof of purchase is required when 
applying for warranty claims. 

Warranty is offered on a Back-to-Base Warranty basis. Where issues can’t be resolved by your Installer or local Reseller in person, or by 
G-Force Staff over the phone, product will need to be returned at Customer Cost to G-Force’s Repair Centre in Bayswater, VIC for 
assessment, repair or replacement.  

Warranty Periods

 

 

Exclusions & Limitations 

The warranties stated herein do not cover damage, malfunction or service failures caused by: 

Failure to follow G-Force or Product Installation, Operation or Maintenance Instructions 

Repair or modifications to your G-Force product by someone other than a G-Force Service Technician, Authorised Installer or 
Reseller 

Abuse, misuse or negligent acts 

Batteries or Fuses supplied with your G-Force product (inc Handset batteries) 

Power failure surges, lightning, fire, water damage, pest damage, accidental breakage, actions of third parties and other events 
or accidents outside of G-Force Automatic Gate’s reasonable control and not arising from normal operating conditions 

G-Force Automatic Gates is not responsible for any special, incidental, consequential or punitive damages arising from the use 

or 

Warranty & Returns 

POLICY

 

 

1

 

year

 

 

DIY

 

Gate Kits

 

Applicable Kits:

  

FG 5, SW 5, DSW 5, SL2000,

 

1

 

year

 

Accessories

 

Such as:  

Push Buttons, Keypads, PE Beams, .

 

3

 

month

 

Spare Parts 

(exclusive of warranty replacements)

 

Such as: 
Control Boards, Receivers, Remote Controls, Limit 
Switches, DC Motors, etc.

 

1

 

Request  

RMA #

 

To lodge a claim, contact G-Force Automatic Gates on 1800 111 930  

 

2

 

Return Goods 
to G-Force

 

Goods are to be returned to G-Force Automatic Gates at the Customer’s cost. G-Force will assess returned 
product within 7 days to determine the extent of warranty cover and likely repair costs

 

 

 

3

 

Repair or Re-
placement of 
Goods

 

In-Warranty

 Repairs will proceed as soon as practicable. The manufacturer’s offering the warranty 

reserves the right to repair or replace product at its discretion. It may, at its discretion, use new, remanufac-
tured, or refurbished parts or products when repairing or replacing product. Replaced parts become the 
property of G-Force Automatic Gates. Repair costs and return freight of in-warranty repairs will be covered 
free of charge

 

Non-Warranty

 Repairs will not proceed until you are notified of estimated Repair Costs, we receive authori-

sation and payment details from you to proceed. Where product is deemed to be unrepairable, and you re-

Summary of Contents for AG 5 DC2




















Reviews: