manualshive.com logo in svg

Future Automation EAD3, Installation Instructions Manual

Share
Download
Future Automation EAD3 Installation Instructions Manual Download Page 8

Page 8 of 17 // Installation Instructions - EAD3

Installation Instructions

2 - Fixing To The Wall

The mechanism must be securely fixed to a solid, load bearing surface using the mounting holes provided 
on the mechanism's wall plate.

1.  Unhook the Screen Uprights (Not Shown Below) from the Main Uprights (Not Shown Below),then remove 

the Top Cover (1.2) and Bottom Cover (1.3) by removing the 8 x M5 fixings shown below, to access the rear 
fixing holes.

2.  Fix the mechanism to the wall using suitable fixings (Not Provided) in as many mounting holes as possible. 

Note: The highlighted fixing holes shown below MUST be used in any installation.

3.  The mechanism may need to be powered out to a mid position to access some central fixing holes (See 

Mechanism Control section of the installation instructions) - 

Note: this should only be done after all 

other fixings are in place. 

Remove 8 x M5 Bolts 

to Release Covers and 

Access Mounting Holes.

Circled Fixing Holes MUST  

Be Used.

1.

2.

1.2

1.3

Summary of Contents for EAD3


















Reviews:

No comments

Brands by name

Popular brands

Load more brands