Fujitsu XG700 - Switch User Manual Download | Manualshive

Page: 130 / 266

background image

XG700 User's Guide

130/266

All Rights Reserved, Copyright (C) PFU LIMITED 2005-2006

Output form (in detailed display)

xg# show spanning-tree detail
Spanning Tree Information 2005/08/22-12:12:15
===============================================================================
Switch Information for Spanning Tree
---------------------------------------------------------------
Spanning Tree

: {Enable | Disable}

Root Switch Priority: 32768
Root Switch ID

: 8000.0080.17C2.0511

Root Path Cost

: 6

Root Port

: port-1

Switch Priority : 32769
Switch ID

: 8001.0080.17C2.0512

Max Age

: 20 (sec)

Hello Time : 2 (sec)
Forward Delay

: 15 (sec)

Topology  Changes   :  0
  Last Topology Change: 2005/08/22-12:12:15
  portfast errdisable : {enabled | disabled}
timeout
  portfast errdisable : 300 sec
timeout  interval
----------------------------------------------------------------

Ports Information for Spanning Tree
-----------------------------------------------------------------------------
[Port 1]
STP  State             :  {Down  |  Discard  |  Learn  |  Forward  }
STP  Mode

: {STP | RSTP | None}

Port ID

: 32772

Role                   :  {Root  |  Designated  |  Alternate  |  Backup}
Path  Cost             :  2
Link  Type             :  {  Point-to-point  |  Shared  }
Forward-Transitions  :  0
Portfast

: {Disabled | Enabled}

  Portfast bpdu-guard : {Disabled | Enabled}
  Portfast bpdu-filter: {Disabled | Enabled}

BPDU  Parameter
Designated  Path  Cost:  0
Designated  Port  ID

: 0

Designated Priority : 128
Designated Root ID

: 0000.0000.0000.0000

Designated Switch ID: 0000.0000.0000.0000
Max Age

: 20 (sec)

Message Age

: 0 (sec)

Message Age Timer

: 0 (sec)

Hello  Time          :  2  (sec)
Hello  Timer         :  0  (sec)
Forward  Time       :  15  (sec)
Forward  Timer       :  0  (sec)
Received  STP  Protocol:  None

[Port 2]

-----------------------------------------------------------------------------
=============================================================================

Switch Information for Spanning Tree

Spanning Tree Protocol information on switch in general is displayed.
The display content is the same as the case of the simplified display.

Ports Information for Spanning Tree

Spanning Tree Protocol information for each port is displayed.

[Port 1]

The switch port number is displayed.

STP State

The state of the port by STP (Spanning Tree Protocol) is displayed.
The display content is the same as the case of the simplified display.

STP Mode

The mode of Spanning Tree Protocol corresponding to the port is displayed. The display content is the same as the
case of the simplified display.

Port ID

The Port ID of the switch port is displayed.

Role

The role of the port is displayed.

−

Root

The root Port.

−

Designated

The designated port.

−

Alternate

The alternate port.

−

Backup

The backup port.

Path Cost

The path cost of the port is displayed.

«
...
128
129
130
131
132
...
»

Summary of Contents for XG700 - Switch











































































































































































































































































Reviews:

No comments

Related manuals for XG700 - Switch

Brand: Keithley Pages: 66

Brand: Cablematic Pages: 8

EdgeSwitch 10 XP

Brand: Ubiquiti Pages: 13

Brand: Paugge Pages: 20

Brand: QSFPTEK Pages: 12

Safeline 2000 Light

Brand: Hisselektronik Pages: 9

Liquipoint FTW33

Brand: Endress+Hauser Pages: 48

Brand: HDTV Supply Pages: 15

Brand: X-keys Pages: 4

Brand: senva Pages: 2

Brand: Guntermann & Drunck Pages: 20

Brand: Accton Technology Pages: 8

IES2016-16T Series

Brand: 3onedata Pages: 3

Brand: Inline Pages: 4

Brand: Pakedge Device & Software Pages: 8

Brand: Black Box Pages: 2

Brand: Jung Pages: 8

IP-Watcher 2x2 Digital PoE

Brand: W&T Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands