Fujitsu XG700 - Switch User Manual Download Page 10 | Manualshive

Page: 10 / 266

background image

XG700 User's Guide

10/266

All Rights Reserved, Copyright (C) PFU LIMITED 2005-2006

1.1 Features

The XG700 is a compact, 12-port 10 Gigabit Ethernet Layer 2 switch, which provides the world's highest level throughput and
least delay.
Special features of the XG700 are shown below:

Item

Function

Features

Throughput 240Gbit/s
Latency 450ns
Switching mode

Either store-and-forward or cut-through is selectable.

MAC address learning table
size

8192 entries

MAC address learning

SVL (Shared VLAN Learning), IVL (Independent VLAN Learning),
user selectable.

Jumbo frame support

Up to 15KB.

Flow control

IEEE802.3x compliant pause frame control. Possible to specify flow
control options for each port: send/receive or receive only.

Storm control

Detects the broadcast storm status to prevent the traffic from
overflowing the network and avoid degrading overall system
performance.

Port security

Possible to restrict port access based on a source MAC address.

Ingress rate control

Supports by-port ingress rate control.

Port mirroring

Possible to monitor the incoming/outgoing traffic by port mirroring.

Basic Switch Functions

Link pass through

Possible to synchronize the link state of a monitored port with the
link state of a single or multiple ports.

Link aggregation
(Static and LACP)

Possible to increase bandwidth and redundancy. (Up to 6 ports for
each link).
Also supports IEE802.3ad LACP.

Scalability

Uplink Filter

Filtering multicast, broadcast and unlearned unicast frames from
leaf nodes to uplink. Possible to configure fat tree using several XG
series.

Redundancy IEEE802.1D

STP,

IEEE802.1w RSTP

Possible to make redundant and loop-free network using Rapid
Spanning Tree Protocol (upward compatible with Spanning Tree
Protocol).

IEEE802.1Q VLAN

Max. 128 groups.

Filtering Ingress/egress filtering

VLAN support

Multiple VLAN

Possible to create multiple Tag-based VLAN, with user VLAN tag
identifier.

QoS IEEE802.1p

QoS

DiffServ

Supports output queue priority control based on VLAN priority or
DSCP (DiffServ Code Point) of IPv4/IPv6.

Multi-cast support

IGMP snooping

Prevents unnecessary forwarding of multicast traffic to ports to
reduce unnecessary multicast traffic.

Traffic statistics

Possible to analyze traffic and errors, using traffic statistics.

Network Management

SNMP agent

Can be used in conjunction with an SNMP manager, supporting
MIBs, including Standard MIB, Bridge MIB, and RMON MIB.

Console by
serial/management LAN

The security of the XG700 is maintained from the serial interface or
dedicated management LAN interface that is independent from the
10 Gigabit ports.

Operation
management

CLI

Allows the user to provide environment settings and operation
management using command line interface (CLI).

«
...
8
9
10
11
12
...
»

Summary of Contents for XG700 - Switch











































































































































































































































































Reviews:

No comments

Related manuals for XG700 - Switch

Brand: Cables to Go Pages: 4

Brand: Harman Kardon Pages: 2

8271 Nways Ethernet LAN Switch

Brand: IBM Pages: 210

Brand: Black Box Pages: 2

SRS Lighting DTS16F-DIN

Brand: plasa Pages: 4

Brand: ATZ Pages: 8

EXT-DVIKVM-441DL

Brand: Gefen Pages: 32

Brand: IOGear Pages: 10

Brand: UNICOM Pages: 1

Brand: Mellanox Technologies Pages: 12

DL-DVI-MUX2-NT SERIES

Brand: G&D Pages: 76

STI Echotel 919

Brand: Magnetrol Pages: 12

DigiTOOLS VS-41USB

Brand: Kramer Pages: 8

TK-205K - PS/2 KVM Switch

Brand: TRENDnet Pages: 11

Brand: Lindy Pages: 5

Brand: Hama Pages: 32

CESRA PIR 10VDC

Brand: DANLERS Pages: 2

Brand: AV Link Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands