manualshive.com logo in svg

Fujitsu XG700 - Switch, User Manual, Page: 241 / 266

Share
Download
Fujitsu XG700 - Switch User Manual Download Page 241

XG700 User's Guide 

241/266

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 

Message 

IDSeverity 

Message/Explanation/Solution 

P3008 
WARNING 

Only 'only-receive' is permitted for flow control when 15KB frame is supported. %1$ 

 

Explanation 

If the jumbo frame size is over 15KB, the setting for flow control is restricted to "only-receive" only. 

 

[[Inserted string]]%1$: Port information 

 

Solution 

If you do not want to set the flow control to "only-receive", the jumbo frame size must be less than 15KB long.

P3009 
INFO 

%1$ has been attached to %2$. 

 

Explanation 

The physical port was attached to link aggregation. 

 

[[Inserted string]]%1$: Physical port information 

 

[[Inserted string]]%2$: Aggregation group information 

P3010 
INFO 

%1$ has been detached. 

 

Explanation 

The physical port was detached from link aggregation. 
[[Inserted string]]%1$: Information on physical port detached 

P3011 
INFO 

%1$ link status details change %2$. 

 

Explanation 

The link status of the port has changed. 

 

[[Inserted string]]%1$: Port information 

 

[[Inserted string]]%2$: New status of the port 

P3012 
INFO 

%1$ state is changed to %2$. 

 

Explanation 

The STP port state was changed.   

 

[[Inserted string]]%1$: Port information 

 

[[Inserted string]]%2$: New state of the STP port 

P3013 
INFO 

Change ingress-bandwidth %1$ %2$ 

 

Explan

a

tion 

Changed the value set in "ingress-bandwidth".   

 

[[Inserted string]]%1$: Port information 

 

[[Inserted string]]%2$: New value of "ingress-bandwidth" 

P3100 
INFO 

%1$ has been created. 

 

Explanation 

Link aggregation was added. 

 

[[Inserted string]]%1$: Aggregation group information 

P3101 
INFO 

%1$ has been deleted. 

 

Explanation 

Link aggregation was deleted. 

 

[[Inserted string]]%1$: Aggregation group information 

P3102 
INFO 

Initialize LPT setting %1$. 

 

Explanation 

The Link Pass Through setting was initialized. 

 

[[Inserted string]]%1$: Port information 

P3103 
INFO 

Released LPT setting %1$ from %2$. 

 
Explanation 

The Link Pass Through setting configured for the port when configuring link aggregation was removed.   

 

[[Inserted string]]%1$: Information on the removed port (to which link status information is sent) 

 

[[Inserted string]]%2$: Information on the monitored port that is to be removed. 

P3200 
INFO 

Learned an IGMP multicast router automatically. vlan-%1$ agg-port %2$ 

 

Explanation 

IGMP snooping learned a multicast router.   

 

[[Inserted string]]%1$: VLAN ID 

 

[[Inserted string]]%2$: Learned aggregation group information 

P3201 
INFO 

Learned an IGMP multicast router automatically. vlan-%1$ port %2$ 

 

Explanation 

IGMP snooping learned a multicast router. 

S3202 
WARNING 

Received IGMP packet without IP header. 

 

Explanation 

Received a frame whose size is smaller that that of the IP header.   
 

Solution 

Investigate the cause of faulty frames being sent to the XG700. 

Summary of Contents for XG700 - Switch











































































































































































































































































Reviews:

No comments