Fujitsu F2MC-8L Series Hardware Manual Download Page 99

Page: 99 / 131

HARDWARE CONFIGURATION

2-79

A/D CONVERTER

[Bit 4] ADCK: External input clock pulse select bit
Bit 4 is used to select the clock pulse for starting by the external input clock
pulse.

No change

Operation started (when EXT bit (bit 1) of ADC2 is 1)

[Bit 3] ADIE: Interrupt specification bit
This bit is used to specify interrupt enable/disable.

Interrupt disabled

Interrupt enabled

[Bit 2] ADMD: Function-switching bit
This bit is used to switch the A/D mode and sense mode.

A/D mode

Sense mode

[Bit 1] EXT: Start type select bit
Bit 1 is used to select the conversion start type.

Starts A/D conversion with AD bit (bit 0) of ADC1

Starts A/D conversion at rising edge of clock selected by
ADCK bit (bit 4) of ADC2

[Bit 0] TEST: Test bit
This bit is used only for testing. Always write 1 at this bit. 1 is always read.

(3) A/D data registers H and L (ADDH and ADDL)

These registers are used to store the results of A/D conversion in A/D mode
and write the comparison set value in the Sense mode. Two upper bits and
eight lower bits are assigned to the ADDH and ADDL, respectively.

ADC1

ADC2

ADDH

ADDL

Address: 001E

Address: 001F

Address: 0020

Address: 0021

Address: 0020

Address: 0021

Initial value

000000XX

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

—

(R/W) (R/W)

(R/W) (R/W) (R/W) (R/W) (R/W) (R/W) (R/W) (R/W)

Initial value

XXXXXXXX

Summary of Contents for F2MC-8L Series




































































































































Search results

Summary of Contents for F2MC-8L Series

Reviews:

Fujitsu F2MC-8L Series, Hardware Manual, Page: 99 / 131

Search results

Summary of Contents for F2MC-8L Series

Reviews: