Fujitsu ETERNUS DX S5 Series Design Manual Download Page 301 | Manualshive

Page: 301 / 335

background image

7. Maintenance/Expansion

Hot Swap/Hot Expansion

"Hot swap" refers to the replacement of components or updating of the firmware while the system is running.
"Hot expansion" refers to the addition of components while the system is running.

ETERNUS DX60 S5

The table below shows whether hot swap or hot expansion for components of the ETERNUS DX60 S5 is possible.

Table 112

Hot Swap and Hot Expansion Availability for Components (ETERNUS DX60 S5)

Component

Hot swap

Hot expansion

Remarks

Controller enclosure (CE)

´

—

Replace the controller enclosure (CE)
when the MP (*1) fails.

Controller module (CM)

¡

(*2)

—

—

System memory

¡

(*2)

—

—

BBU

¡

(*2)

—

—

BUD

¡

(*2)

—

—

Controller firmware

¡

(*2) (*3)

—

—

SFP+

¡

(*2)

¡

—

iSCSI port

—

¡

—

SAS port

—

¡

—

Power supply unit (PSU)

¡

—

—

Disk (HDD)

¡

¡

—

SSD

¡

¡

—

Operation panel (PANEL)

´

(*4)

—

—

Disk firmware

¡

(*3)

—

—

Drive enclosure (DE)

¡

¡

Replace the drive enclosure (DE)
when the MP (*1) fails.

Power supply unit (PSU)

¡

—

—

Disk (HDD)

¡

¡

—

SSD

¡

¡

—

Operation panel (PANEL)

´

(*4)

—

—

I/O module (IOM)

¡

—

—

Disk firmware

¡

(*3)

—

—

¡

: Allowed /

´

: Not allowed (cold swap is possible) / —: Not applicable

*1:

Mid Plane. This is a board that is located between the front (drive side) and rear (controller (CM) or I/O module (IOM) side) of the
ETERNUS DX.

*2:

When a multipath configuration is used, switch to the host paths of the CM that will not have maintenance performed to continue
operation.

*3:

An I/O suspension may be required depending on the firmware changes.

*4:

Operation can be continued during a failure. The status of the ETERNUS DX can be monitored via ETERNUS Web GUI or ETERNUS CLI.

301

Design Guide

«
...
299
300
301
302
303
...
»

Summary of Contents for ETERNUS DX S5 Series
















































































































































































































































































































































Reviews:

No comments

Related manuals for ETERNUS DX S5 Series

G-DRIVE mobile USB

Brand: G-Technology Pages: 18

Brand: G-Technology Pages: 34

FlashPen "Piko"

Brand: Hama Pages: 4

Data Driver DPD-100

Brand: Hyun Won Pages: 15

Brand: SanDisk Pages: 2

Brand: OCZ Pages: 3

Brand: NEC Pages: 254

Brand: AIC Pages: 105

Paletto 00108043

Brand: Hama Pages: 4

Brand: Wolfcraft Pages: 96

Brand: HOGYME Pages: 31

HPRO72TLOCKERBLK

Brand: Husky Pages: 8

Brand: Argosy Pages: 1

Brand: Décor et Jardin Pages: 20

DiskGO 222802-PE

Brand: Edge Pages: 1

Superstor GL-119

Brand: HTP Pages: 12

Brand: Datoptic Pages: 24

BUSH RANGER 3023BRK

Brand: ABSCO SHEDS Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands