Fuji Xerox DocuCentre S2011 Basic Operation Manual Download Page 54

Page: 54 / 56

Problem Solving

093-956

[Cause]

There is no more toner in the toner cartridge.

[Remedy] Remove the seal on the drum cartridge.

093-959

[Cause]

An error occurred with the drum cartridge.

[Remedy] Replace the drum cartridge. Contact your local Fuji Xerox representative or sales

representative.

116-317
116-321
116-323

[Cause]

An error occurred.

[Remedy] Switch off the machine power, make sure that the display is blank, and then

switch on the machine power. If the same message is displayed again, contact
our Customer Support Center.

116-324

[Cause]

An error occurred.

[Remedy] The machine will automatically recover. Wait for a while, and try again.

116-334
116-377
116-390

[Cause]

An error occurred.

[Remedy] Switch off the machine power, make sure that the display is blank, and then

switch on the machine power. If the same message is displayed again, contact
our Customer Support Center.

116-747

[Cause]

Unable to complete scanning due to the scanning area being too small.

[Remedy] Decrease the value of the Edge Erase or reduce the zoom ratio.

Error Code

Cause and Remedy

Summary of Contents for DocuCentre S2011
























































Search results

Summary of Contents for DocuCentre S2011

Reviews:

Related manuals for DocuCentre S2011

Brands by name

Popular brands

Fuji Xerox DocuCentre S2011, Basic Operation Manual

Search results

Summary of Contents for DocuCentre S2011

Reviews:

Related manuals for DocuCentre S2011

Brands by name

Popular brands