Freescale Semiconductor SC140 DSP Core Reference Manual Download Page 224 | Manualshive

Page: 224 / 760

background image

5-44

SC140 DSP Core Reference Manual

Processing States

5.7.5 Debug State

The debug state is a special core processing state in which the pipeline is stalled and waits for user
commands from the JTAG or EOnCE. The core can enter the Debug state in the following cases:

•

JTAG issues a debug request is asserted, in all states.

•

The EE0 EOnCE signal is asserted during reset.

•

The EE0 EOnCE signal is asserted anytime, if programmed as a debug request input in the
EE_CTRL register.

•

An EOnCE Debug state event occurs.

•

A DEBUG instruction is executed, if the SDD in EMR is not set, and the EOnCE is programmed
so that it will generate a Debug state event.

•

A DEBUGEV instruction is executed, and the EOnCE is programmed so that it will generate a
Debug state event.

If EE0 or the JTAG debug request are asserted during reset and continue to be asserted when reset is
de-asserted, the core enters the debug state without executing any instruction.

The debug state is exited by setting the exit bit in the EOnCE command register by JTAG. Refer to

Chapter 4, “Emulation and Debug (EOnCE),”

for a detailed description of the user commands in the

debug state.

5.7.6 Wait Processing State

The wait processing state is a low-power consumption state entered by the execution of the WAIT
instruction. After a system-specific delay of some cycles from the issue of the WAIT instruction, the core’s
global clock is turned off. Peripherals can continue to operate, but all internal processing is halted until one
of the following actions occurs:

•

An interrupt, with enabled priority, is issued

1

.

•

A non-maskable interrupt (NMI) request is issued.

•

A low-level is applied to the RESET signal (RESET asserted).

•

The JTAG issues a debug request.

•

The EOnCE EE0 signal (programmed as a debug request input) is asserted.

Debug request from the EOnCE may also exit from Wait Processing State, if it occur a few cycles after the
WAIT instruction execution (exact time may vary according to the specific clock scheme implemented).

If an exit from the Wait Processing State is caused by assertion of the EE0 signal or a debug request, the
core either enters the debug state immediately, or the debug exception is serviced according to the EOnCE
configuration. Refer to

Chapter 4, “Emulation and Debug (EOnCE),”

, for further details.

If the Wait Processing State is exited by assertion of the RESET signal, the core enters the reset processing
state.

Table 5-18 describes exit from Wait Process State, due to interrupt and NMI, under various core
conditions.

1. i.e. IPL of the interrupt is greater than the core IPL, as determined by bits I2-I0 of the SR. See Table 5-18 for more information.

«
...
222
223
224
225
226
...
»

Summary of Contents for SC140 DSP Core

























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SC140 DSP Core

Brand: IBM Pages: 86

Brand: CAME Pages: 4

Brand: 3Com Pages: 8

Brand: Farallon Pages: 26

Brand: Observint Pages: 11

Brand: TC-Helicon Pages: 2

EK-FC980 GTX Classy

Brand: ekwb Pages: 2

REJ06B0734-0100

Brand: Renesas Pages: 19

Brand: ANEP Pages: 48

FireWire 800 ExpressCard 34

Brand: LaCie Pages: 24

Brand: ZiLOG Pages: 11

LEDWALL Optimizer HQ P2

Brand: Gundermann VIDEOWALL Pages: 12

Mustang-M2AE-MX1

Brand: IEI Technology Pages: 58

Brand: ZyXEL Communications Pages: 23

Brand: Variscite Pages: 17

Brand: Intellinet Pages: 2

Brand: VIA Technologies Pages: 2

SteelCentral NetExpress 470

Brand: Riverbed Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands