manualshive.com logo in svg

FRC Turbofoam TFC100, User Manual

Share
Download
FRC Turbofoam TFC100 User Manual Download Page 65

TFC100 Rev180215

65

Figure W8.  Summing Box Wiring 

CONNECTOR J2

12-Pin Connector/Cable

Pin/Wire 

Description

1/Red   

5 VDC

2/Black 

Sensor Ground

3/White 

Sensor 3 Signal

4/Red   

5 VDC

5/Black 

Sensor Ground

6/White 

Sensor 4 Signal

7/Red   

5 VDC

8/Black 

Sensor Ground

9/White 

Sensor 5 Signal

10/Red  

Sensor  +5 VDC

11/Black 

Sensor Ground

12/White 

Sensor 6 Signal

CONNECTOR J1

12-Pin Connector/Cable

Pin/Wire 

Description

1/Red  * 

Supply Power

2/Black* 

Supply Ground

3/Green* 

FRC Datalink (–)

4/White* 

FRC Datalink (+)

5/Black 

FRC Datalink (–)

6/Red   

FRC Datalink (+)

7/Red   

5 VDC

8/Black 

Sensor Ground

9/White 

Sensor 1 Signal

10/Red  

Sensor  +5 VDC

11/Black 

Sensor Ground

12/White 

Sensor 2 Signal

Summing Box (Multiple Flow Sensors Only)

The summing box has two 12-Pin connectors. Each box has inputs 

for six (6) discharge flow sensors. Multiple boxes are interconnected using 

the FRC datalink. Power is provided by the control model.

CONNECTOR J1

CONNECTOR J2

Summing Box 

Top View

Pin 1

*Four conductor cable 

from control module.

Note:

 When more than one box is installed the address 

of each box must be set. Refer to Installation Section.

Flow Sensor

Systems with a single discharge flow sensor: The sensor cable is connected directly to the control module.
Systems with multiple flow sensors: The sensor cables are connected to a summing box. The summing box 

is connected to the control module via a supply power and FRC datalink cable.

Figure W7.  Flow Sensor Wiring 

SENSOR CABLE

3-Pin Connector

Pin/Wire 

Description

A/Black Ground

B/Red   

Supply Voltage

C/White Signal 

Sensor Cable

Signal 

Output

Supply 

Voltage

Ground

Flow Sensor 

Top View

Note:

 If FRC flowmeters (DFA or FPA) are used to retrieve flow rate 

information, only the FRC Datalink is connected to the foam system.

IMPORTANT

 the flowmeter ID numbers must be different than the 

flow sensor ID numbers used with a summing box.

Summary of Contents for Turbofoam TFC100

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands