manualshive.com logo in svg

FRC Turbofoam TFC100, User Manual

Share
Download
FRC Turbofoam TFC100 User Manual Download Page 55

TFC100 Rev180215

55

Saddle Clamp Installation

Note:

 Ensure that the mounting location meets the requirements for uniform water flow and that there 

is enough room for the saddle clamp, sensor, and connector to fit.

1.  Drill and deburr a 1-11/16" to 1-3/4" diameter hole at mounting location.
2.  Clean pipe surface in area where saddle clamp gasket seal.

Note:

 The sensor housing is epoxied in the saddle clamp with the alignment tab in the correct position 

and is not meant to be removed.

3.  Place saddle clamp over hole with sensor housing centered.
4.  Tighten saddle clamp nuts until the gasket makes a good tight seal.

5.  Insert flow sensor into sensor housing. Align flat spot on sensor rim with alignment tab and make sure 

O-ring is in groove.

Note:

 The retainer cap is hand-tightened. There is an inside lip that stops the cap from turning when 

it makes contact with the alignment tab. This provides the correct pressure to make the seal at the 

O-ring. Make sure the flow sensor engages the alignment tab and does not rotate.

6.  Install retainer cap and hand tighten.

7.  Connect flow sensor cable. (Refer to Wiring Section.)

Figure L12.  Saddle Clamp Installation

Note:

 Dimensions are typical and are an aid 

to determine flow sensor mounting locations.

Pipe Size 

Dimensions

(Sch 40)  

A 

B 

C

  2 

 

5.5 

3.9 

2.9

  2.5 

 

5.5 

3.9 

2.8

  3 

 

5.9 

3.9 

2.8

  3.5 

 

6.8 

4.3 

2.8

  4 

 

6.8 

4.3 

2.8

  5 

 

8 

4.3 

2.8

Measurements are in inches.

A

C

B

Retainer Cap

O-Ring

Paddlewheel 

Flow Sensor

Sensor 

Housing
Saddle 

Clamp

Alignment Tab

Note

: Allow a minimum of 3 inches clearance above 

the sensor for removal/installation.

Note:

 When the retainer cap is tightened 

make sure the flow sensor engages the 

alignment tab and does not rotate.

Summary of Contents for Turbofoam TFC100

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands