FRC Turbofoam TFC100 User Manual Download Page 61

Page: 61 / 88

TFC100 Rev180215

Figure W2. Control Module Wiring

12-Pin Connector/Cable

Pin/Wire

Description

1/Red

Supply Power

2/Black Ground

3/Red

Sensor 5 Volt

4/White

Sensor Signal

5/Green

Flush Indicator

6/White

Flush Switch

7/White

FRC Datalink (+)

8/Green

FRC Datalink (–)

9/Black Ground

Supply Power (* Tank Empty)

11/Green

Remote ON/OFF Indicator

12/White

Remote ON/OFF Switch

6-Pin Connector/Cable

Pin/Wire

Description

1/Green

Tank A Empty Sensor

2/Yellow

Tank B Empty Sensor

3/White

Select A/B Sensor

4 Spare

5 Spare

6 Spare

Control Module

The control module communicates with other components of the system via the 2-wire FRC datalink.

The datalink is also used to communicate with other FRC products such as the TankVision Pro.

*Pin 10 is Tank Empty Sensor (active low) for TFC100 Only

6-Pin Connector Notes:

- The Tank Empty inputs are used with tank float switches.

- The Select A/B Sensor input is used when the TFC200 is

installed with a manual ABF selector assembly.

TFC100

TFC200/300/400

Pin 1

Vent

USB

Port

Pin 1

USB

Port

Vent

*NOTE:

If opened, USB access port plug

must be tightened to a torque of 8-10 in-lbs.

Exceeding this torque value can result in

damage to its water seal capability.

Warning: Flange may not fully bottom out.

Summary of Contents for Turbofoam TFC100

























































































Search results

Summary of Contents for Turbofoam TFC100

Reviews:

Brands by name

Popular brands

FRC Turbofoam TFC100, User Manual

Search results

Summary of Contents for Turbofoam TFC100

Reviews:

Brands by name

Popular brands