manualshive.com logo in svg

FRC Turbofoam TFC100, User Manual

Share
Download
FRC Turbofoam TFC100 User Manual Download Page 51

TFC100 Rev180215

51

Hose Sizes:

 

Hoses Provided by Installer

Standard Fittings are NPT (National Pipe Taper)

Use shortest hose runs possible for concentrate hose lines;

Pump input needs 10" minimum of hose for vibration absorption.

Figure L8.  TFC200 Plumbing Two Tank System w/Manual ABF Selector

Standard All Pumps:

1/2" Female

Standard All Pumps:

1/2" Female

Standard All Pumps:

1/2" Male

Standard All Pumps:

3/4" Male

Clear Suction Hose

23" (584mm) Hg Vacuum; 50 PSI (3 bar)

1.6, 2.6 GPM Pumps: 

      3/4" (19mm) ID

3.5, 5.0, 6.2, 6.5 GPM Pumps:  1" (25.4mm) ID

Pressure Hose

500 PSI (34 bar)

Standard All Pumps:  1/2" (13mm) ID

Pressure Hose

500 PSI (34 bar)

Standard All Pumps:  1/2" (13mm) ID

Clear Suction/Pressure Hose

23" (584mm) Hg Vacuum; 500 PSI (34 bar)

1.6, 2.6 GPM Pumps: 

      3/4" (19mm) ID

3.5, 5.0, 6.2, 6.5 GPM Pumps:  1" (25.4mm) ID

Fitting Sizes:

 

Fittings Provided with System Kit

1.6 and 2.6 GPM Pumps:

3/4" Female

3.5, 5.0, 6.2, 6.5 GPM Pumps:

1" Female

1.6 and 2.6 GPM Pumps:

3/4" Male

3.5, 5.0, 6.2, 6.5 GPM Pumps:

1" Male

Standard All Pumps:

3/4" Female

Summary of Contents for Turbofoam TFC100

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands