background image

6

EN

If the device, especially gas control system components or the burner has been flooded, switch off 

the device and consult a technical department or a qualified serviceman in order to check whether 

the reuse will require replacement of any of the system components.

The device is for external use only or for use in a well ventilated areas!

A well-ventilated space must have 25% of its surface exposed. This area is determined on the 

basis of the sum of the wall surfaces of the given usable space.

Due to the possibility of high temperatures of all surfaces of gas garden fireplaces and due to po-

ssible exposition to the fire, all flammable materials should be located at a safe distance from the 

device.

Elderly people, children and other unconscious persons should be informed and warned of the 

possibility of high temperatures occurring on the appliance during its operation and immediately 

after it is extinguished, and should avoid contact with the appliance to prevent burns and ignition 

of clothing.

Children, infants, infirm people and other people who require special attention that can be close 

the appliance should be subject to special supervision. These persons may be particularly exposed 

to accidental contact with the apppliance. If necessary, use safety barriers to limit access to the 

applinace.

NEVER obstruct THE VENTILATION ROOM OF A GAS CYLINDER!

Under no circumstances any of solid fuels (wood, paper, coal, etc.) shall be used in this appliance.

IT IS STRICTLY PROHIBITED 

to use any liquid fuels or other flammable materials to light the ap-

pliance!

To avoid accidents, it is not recommended to allow the use of the device to persons not familiar 

with the operation of the device. For safety, always use gloves and goggles for maintenance.

- Always make sure that the gas supply is cut off before checking, servicing or cleaning the device.

Do not hit or lean against any part of the apppliance.

ATTENTION:

 No elements in the appliance may be replaced by other parts than those provided by 

the manufacturer or recommended by the manufacturer.

Use only the gas type and gas cylinder type specified by the manufacturer. In case of strong wind, 

protect the device against gusts or turn it off.

SAFETY INFORMATION

SET COMPONENTS - FIRST UNPACKING OF THE PURCHASED HEATER

If any damage or deficiencies are noticed during the consignment inspection, please contact your 

authorized dealer.

Please make sure that all parts of the set are not damaged during transport. The check should take 

place in the presence of the supplier. The purchased heater should contain a complete gas cylinder 

connection kit.

Summary of Contents for OUTDOORFIRE B


























Reviews: