FPS PowerSewer V4PS Installation, Operation & Maintenance Manual Download Page 29

29

POWERSEWER® 3 YEAR WARRANTY STATEMENT

LIMITED WARRANTY

THIS WARRANTY (“WARRANTY”) SETS FORTH THE COMPANY’S SOLE OBLIGATION AND PURCHASER’S EXCLUSIVE REMEDY FOR DEFECTIVE PRODUCT.

Franklin Electric Co., Inc. and its subsidiaries (the “Company”) warrants that the products accompanied by this Warranty are free from defects in materials or workmanship that exist at 
the time of sale by the Company and which occur or exist within the applicable warranty period identified below. Any distributor, sub-distributor, recipient, end-user and/or consumer 
agrees that by accepting the receipt of the products, the distributor, sub-distributor, recipient, end user and/or consumer expressly agrees to be bound by the terms of this Warranty.

I. Applicable Warranty Period

The products accompanied by this Warranty shall be covered by this Warranty for a period of 36 months from the date of original purchase. In the absence of suitable proof of 
purchase date, the warranty period of this product will begin to run on the product's date of manufacture.

III. Replacement Parts

1. 

Replacement parts will receive a 12-month warranty from the date of purchase.

III. Instructions Applicable to this Limited Warranty

1. 

Consumers wishing to submit a warranty claim must return the products accompanied by this Warranty to the point of purchase for warranty consideration.

2. 

Consumer must retain proof of purchase and installation documents. Installation documents to be completed by Service Representative at the time of unit start-up.

3. 

Upon discovery of a potential defect, any personal injury, property damage or any other type of resulting damage, if applicable, shall be reasonably mitigated to the extent possible.

4.  Consumer must notify the Company or Service Representative within two (2) days after discovering a potentially defective product or part.
5. 

All warranty service or repair must be performed by the Company or a Service Representative.

6.  All return of parts to the Company for evaluation and/or repair should be made through a Service Representative. If you are not sure of the Service Representative  

in your area, call toll free 1-866-271-2859.

7. 

At its discretion, the Company may inspect products either at its facilities or in the field, and after determination of a warranty claim, will, at its option, repair or replace 
defective parts. Repaired or replaced parts will be returned freight prepaid by the Company.

8. 

This Warranty does not cover any labor or shipping charges. The Company shall not be liable for any costs or charges attributable to any product testing, maintenance, 
installation, repair or removal, or for any tools, supplies, or equipment needed to install, repair, or remove any product.

IV. Limitations Applicable to this Limited Warranty
THIS WARRANTY DOES NOT APPLY TO ANY OF THE FOLLOWING:

1. 

Any product on which any maintenance or repair service is performed by any person other than the Company or a Service Representative authorized by the Company  
(“Service Representative”);

2. 

Any product that is not installed, applied, maintained and used in accordance with the Company's published instructions, applicable codes, applicable ordinances  
and/or with generally accepted industry standards.

3. 

Any product that has been subject to misuse, misapplication, neglect, alteration, accident, abuse, tampering, acts of God (including lightning), acts of terrorism,  
acts of war, fire, improper storage or installation, improper use, improper maintenance or repair, damage or casualty, or to an excess of the recommended  
maximums as set forth in the product instructions.

4.  Any product that is operated with any accessory, equipment, component, or part not specifically approved by the Company.
5. 

Use of replacement parts not sold by the Company, the unauthorized addition of non-Company products to other Company products,  
and the unauthorized alteration of Company products.

6.  Products damaged by normal wear and tear, normal maintenance services and the parts used in connection with such service, or any other  

conditions beyond the control of the Company.

7. 

Any product that has been used for purposes other than those for which it was designed and manufactured.

8. 

Any use of the product where installation instructions and/or instructions for use were not followed.

9.  Products connected to voltage other than indicated on the product’s nameplate.
10.  Products where the pump was exposed to any of the following: sand, gravel, cement, grease, plaster, mud, tar, hydrocarbons, hydrocarbon derivatives  

(oil, gasoline, solvents, etc.) or other abrasive or corrosive substances.

11.  A pump, which is not activated within two months of installation, unless the Company or a Service Provider provides service to the pump before activation.  

The cost of this service is the responsibility of the owner.

12.  Products in which the pump has been used for pumping of liquids above 140°F.
13.  Products in which the pump was allowed to operate dry (fluid supply cut off).
14.  Products in which the sealed motor housing has been opened or the product has been otherwise dismantled by customer.

Summary of Contents for PowerSewer V4PS

































Reviews: