FPS PowerSewer V4PS Installation, Operation & Maintenance Manual Download Page 2

BEFORE GETTING STARTED

The following symbols will appear throughout these installation, operation and maintenance instructions for your benefit and to assist you in the 
installation, operation and maintenance of the PowerSewer® grinder pump pressure sewer system.

This is the safety alert symbol. When you see this          symbol on the equipment or in the instructions, look for one of the following signal 
words and be alert to the potential for personal injury, death or property damage.

DANGER

 warns about hazards that will cause serious personal injury, death or major property damage if ignored.

WARNING

 warns about hazards that can cause serious personal injury, death or major property damage if ignored.

CAUTION

 warns about hazards that will or can cause minor personal injury or major property damage if ignored.

NOTICE

 indicates special instructions which are important but not related to hazards. Carefully read and follow all safety 

instructions in this manual and on pump.

WARNING

 This equipment is intended for installation, operation and maintenance by technically qualified personnel. 

Failure to install, operate and maintain it in compliance with national, state and local electrical and safety codes and Franklin Electric 

installation, operation and maintenance instructions may result in electrical shock or fire hazard, personal injury or death, unsatisfactory 

performance, equipment failure, and will void the warranty. If you have any questions, call your local commercial Franklin Electric Sales 

Representative or Franklin Electric Technical Services at 866-271-2859.

WARNING

 This equipment is not designed for use with hazardous, flammable liquids and gases. These liquids and  

gases may be present in containment areas. This equipment shall not be installed in locations classified as hazardous in accordance with 

National Electric Code (NEC), ANSI/NFPA 70.

WARNING

 Hazardous voltage can shock, burn or cause death. Failure to disconnect and lock out all electrical power 

before attempting installation and maintenance can shock, burn or cause death.

WARNING

 Biohazard can cause serious personal injury. Grinder pump and attached valves and piping must be flushed 

and disinfected inside and out prior to performing any maintenance.

WARNING

 Hazardous machinery can cause severe personal injury. Rotating cutter assembly is very sharp and  

can cause severe personal injury.

WARNING

 Hazardous voltage can shock, burn or cause death. Do not lift, carry or hang pump by the electrical cable. 

Damage to the electrical cable can cause shock, burns or death.

CAUTION

 This is a sewage-handling pump and must be vented in accordance with national, state and local plumbing codes.

W A R N I N G

W A R N I N G

SAFETY INSTRUCTIONS

Summary of Contents for PowerSewer V4PS

































Reviews: