Model D2424LV Reference Manual (Chain Play function)
59
Setup of the Chain Play List
The chain play list is setup via the “
Chain Play List?
” menu in the SETUP mode.
The following procedure is based on the assumption that a multiple number of programs are in the current
drive and that a tune is recorded in each program.
1. Enter the SETUP mode by pressing the [SETUP] key
while the D2424LV is in the stop mode.
2. Use the Jog dial to display the “Chain Play List?,”
and then press the [EXECUTE/YES] key.
The display will change to setup of the play list.
Flashing
This display indicates the initial setting in which no
chain list is setup (“
EE
” means “
invalid
.”).
The chain play number can be set in the currently
blinking section (left) and numbers “
01
” through “
99
”
can be input via the Jog dial.
Also, the flashing section can be moved from the left
“
01
” to the right “
EE
” by pressing the [
EXECUTE/YES
]
key, and except for “
EE
,” each program number
currently in the disk can be selected via the Jog dial.
3. Input the chain number via the Jog dial and press
the [EXECUTE/YES] key.
The flashing section will move from left to the right
“
EE
.”
4. Select the desired program number via the Jog dial
and press the [EXECUTE/YES] key.
The chain number of the selected program will be set
and, the same as in <Step 2>, the left section will flash.
For example, if it has been set as shown below, the
setting will be for playback of the program 5 tune in
the second order.
Repeat these procedures to set up the chain play
number in the desired program.
<Setup example of the chain play list>
As an example, if the chain play list is set as
shown below, chain play is possible in the
order of: program 3 - program 5 - program 2.
If the chain list is to be ended after program
1, as shown in the example below, set “
EE
” at
fourth (“
c04
”) in the chain list.
By selecting “
EE
,” the chain play list setting
will be “
c01
” - “
c03
,” and beyond “
c04
” will be
invalid.
“
EE
” can be selected with the Jog dial while
the right program number is flashing.
<Note>
• In order to execute chain play, “
AUTO RTN
START point
” and “
AUTO RTN END point
” must be
setup in each program to be played back.
Refer to previous page “50” for how to register
memory points.
• If the chain play list is edited even once, the
Chain Play Mode will be set “
OFF
.”
In such case, after setup of the chain play list,
reset the Chain Play Mode to “
ON
” .
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
PGM
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Flashing
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
