43
Model D2424LV Reference Manual (Punch In/Out)
6. When you finish rehearsing, press the [STOP]
button.
If you are still unsatisfied, repeat steps 3-5.
Cancelling Rehearsal mode
1. While holding down the [STOP] button, press the
foot switch.
The display shows “
Rehearsal Off
” for 1 second, then the
flashing REHEARSAL LED turns off and cancels the
rehearsal mode.
<Hint>
To rehearse repeatedly, set the AUTO RTN START point
slightly before the Punch In point, and the AUTO RTN
END point slightly before the Punch Out point.
This will help you concentrate on your performance or
check the recording level easily (especially since Manual
Punch In/Out involves operating the foot switch
operation as well as the recorder). (See <Hint-2> in the
“Rehearsing Auto Punch In/Out recording” for more
information.)
Model 8051 Foot switch
Manual Punch In/Out
This section explains how to perform Manual Punch In/Out using a foot switch (optional Model
8051). You do not need to specify the Punch In/Out points. Instead, you press the foot switch at
the Punch In/Out point. Manual Punch In/Out also offers rehearsal and actual takes. You can
repeat rehearsal until you are ready. As an example, replace a part of the recorded guitar solo on
track 3.
• Initialize the recorder.
• Select a desired Program for Punch In/Out.
• Check a sampling frequency of the recorder and external device.
Preparation
Check to see that the guitar is connected to the input
jack of the mixer, as required for [AUTO PUNCH IN/
OUT] mentioned earlier.
1. Connect an optional foot switch (Model 8051) to
the PUNCH IN/OUT jack on the rear panel.
Rehearsing Manual Punch In/Out recording
In Rehearsal mode, the READY track enters input
monitoring mode between the Punch In and Out
points (the points at which you press the foot
switch), and the sound is not recorded. You can
practice the Punch In/Out operation repeatedly
before you proceed to actual recording.
1. Press the foot switch while holding down the
[STOP] button.
“
Rehearsal On
” will appear on the display or about 1
second, then rehearsal mode will appear and the
REHEARSAL LED (green) of the [
AUTO PUNCH
] key flashes.
2. Press the [RECORD TRACK] select key [3/11/19]
to set track 3 to READY.
3. Press the [PLAY] button to play back from a point
slightly before the Punch In point.
4.Play the guitar accompanying the playback of
tracks 1 to 8.
The recording level and monitor volume is adjusted on
the mixer in the same manner as done for [AUTO PUNCH
IN/OUT] described earlier.
5.Press the foot switch once at the desired Punch
In point, then press the foot switch again at the
desired Punch Out point.
The rehearsal mode will operate as shown in the figure.
Between the Punch In and Out points the current
performance of the guitar will be played as the guitar
monitor sound. The previous recording is heard in any
other case. The RECORD LED lights up when Punching
In and turn off when Punching Out (the REHEARSAL
LED remains flashing).
2.Set the foot switch function to “Punch I/O” (punch
in/out function) by the SETUP mode “Setup of the
foot switch function” menu.
REHEARSAL
TAKE
AUTO
PUNCH
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
Track 7
Track 8
This part is changed.
Playback end point
Playback start point
Punch In point
(Rehearsal In)
Punch Out point
(Rehearsal Out)
All tracks are in playback
monitoring mode.
Press the foot switch
at the Punch In point.
Only track 3 in input monitoring.
The sound is not recorded
at this time. The RECORD
LED flashes.
All tracks are in playback
monitoring mode.
Press the foot switch
at the Punch Out point.
