118
Model D2424LV Reference Manual (Changing the Initial Settings <SETUP mode>)
Flashing
Recording enabled/disabled
1.While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
2.Turn the Jog dial to select “Rec Protect ?” (“?”
flashes), then press the [EXECUTE/YES] key.
The current setting appears on the display.
Pressing the [
EXECUTE/YES
] key turns off the flashing
“
?
” character, and the recording enabled/disabled
indicator flashes. With the initial setting, “
Off
” flashes
as shown below.
3.Use the Jog dial to enable or disable recording.
Rotating the
Jog
dial clockwise and counter-clockwise
will flash “
On
” and “
Off
” alternately.
Selecting “
Off
” enables recording; you can record, paste,
and erase data.
Selecting “
On
” disables recording; and you cannot
record, paste, or erase data.
<Note>
When recording is disabled (On) and you try to record,
paste, or erase data, the recorder displays “Protected”
for a second, indicating that you cannot perform the
operation. To perform the operation, you need to
enable recording (Off).
4.Press the [EXECUTE/YES] key.
To cancel the operation, or to restore the setting
obtained prior to the
[EXECUTE/YES]
key press, press
the
[STOP]
button or the
[EXIT/NO]
key. Each time you
press one of these keys, the recorder returns to the
previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.
Setting digital input (“D. in ?” menu)
In the “
Setting a digital input
” menu, the signal to be input to the
[DATA INPUT]
connector of the recorder can be
set for either digital signals (adat digital signal or S/P DIF digital signal) or analog signals, and also setup of the
digital in clock (synchronous or asynchronous).
By using this function, signals from external digital equipment (CD, MD, DAT, adat digital mixer) can be
digitally recorded.
When selecting the clock, there are the “
Async
” and “
Sync
” modes; either should be selected depending on the
application. If it is set to “
Async
” mode, the later explained “
Clock Sel?
” (Setting the operating clock) should
be setup in accordance to the application.
• Initial setting:
[Analog]
• Assignable digital signal/setting digital in-clock:
[adat: Async]
(adat digital signal/Asynchronous mode)
[adat: Sync]
(adat digital signal/Synchronous mode)
[SPDIF: Async]
(S/P DIF digital signal/Asynchronous mode)
[SPDIF: Sync]
(S/P DIF digital signal/Synchronous mode)
[Analog]
(not assigned digital signal)
* This setting is shared by all Programs in the same disk.
* The settings cannot be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the recorder.
<Function of the [DATA INPUT] connectors>
<Setup for analog signals>
If the digital input is set up for Analog (Initial setting), digital signals cannot be input at
[DATA INPUT] 1-8
,
9-16
and
17-24
of the D2424LV.
<Setup for S/P DIF digital signals>
If the digital input is set up for S/P DIF (Async or Sync), only
[DATA INPUT] 1-8
can be used.
S/P DIF digital signals input to
[DATA INPUT] 1-8
will be assigned and recorded in tracks 1 and 2 of D2424LV.
<Setup for adat digital signals>
If the digital input is set up for adat (Async or Sync),
all [DATA INPUT]
connectors can be used.
Adat digital signals input to
[DATA INPUT] 1-8
will be assigned and recorded in tracks 1-8; the signals to
[DATA
INPUT] 9-16
in tracks 9-16; and the signals to
[DATA INPUT] 17-24
in tracks 17-24.
Note
: The
[DATA INPUT]
connectors do not support 96kHz FS adat digital signals.
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT