42
Model D2424LV Reference Manual (Punch In/Out)
Auto Punch In/Out Take
After you are satisfied with your rehearsal, you
can proceed to an actual take of Auto Punch
In/Out.
You can undo or redo Auto Punch In/Out
recording if you change your mind. The control
panel settings are the same as those for
rehearsal.
1. Press the [RECORD TRACK] select key [3/11/19]
to set track 3 to READY.
2. Locate a point slightly before the Auto Punch In
point.
3. Confirm that Auto Punch mode is turned on.
Press the [
AUTO PUNCH
] key to turn on the function, if it
is not already on (REHEARSAL/TAKE LED flashes).
4. Press the [RECORD] button while holding down
the [PLAY] button.
Only TAKE LED (red) lights up and starts TAKE.
• Track 3 indication on the display will only light up
between the AUTO PUNCH IN/OUT point, and will
flash in any other case.
• When the Auto Punch Out point is passed, the recorder
cancels Auto Punch mode automatically, and nothing
appears in the A. PUNCH display area.
<Caution after Punch Out>
In an FS=44.1kHz program, the simultaneously
recordable number of tracks is a maximum of 8.
In an FS=88.2/96kHz program, the maximum is 2 tracks
in which “seamless punch out” without mute can be
executed.
In simultaneous recording beyond this number, the
recorder will be muted for 3-5 seconds after punch out
but during actual recording, it will be a seamless punch
out. Depending on the speed of the hard disk being
used, when recording a fewer number of simultaneous
tracks than mentioned above, the recorder will also be
muted, but this poses no problem during actual
recording.
6. Play track 3 to check the result of the Auto Punch
In/Out operation.
If you fail with AUTO PUNCH IN/OUT and are not
satisfied, repeat the process by performing the AUTO
PUNCH IN/OUT undo operations described in the next
section.
Single Undo/Redo
You can single undo or redo Auto Punch In/
Out recording.
Press the [
UNDO/REDO
] key after recording is
complete to restore the conditions that existed
prior to the recording.
Press the [
UNDO/REDO
] key again to restore the
conditions that existed after the recording.
However, the procedures explained here is for
Single Undo/Redo and there are limitations as
written in the Notes below. If the current drive
was formatted with the multiple undo function
ON, Multiple Undo is also possible.
Refer to page “
66
” for details on the
Multiple
Undo function
.
<Notes at executing single undo/redo>
Note-1
: This function only works when this
recorder is in the stop mode.
Note-2
: After finishing auto punch in/out, please
note that single Undo/Redo is not possible if the
following have been executed.
• If a new recording has been made.
• When a new editing job is executed (such as
Copy & Paste, Move & Paste, or Erase).
• When in the AUTO PUNCH ON mode, when
the AUTO PUNCH IN point is passed in the
PLAY (or RECORD) mode.
• If the power was switched off.
• If program select was executed.
• When multiple undo is executed.
5. When you finish recording, press the [STOP]
button.
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
Track 7
Track 8
This part is changed.
Playback end point
Playback start point
Auto punch In point
(Take In)
Auto punch Out point
(Take Out)
All tracks are in playback
monitoring mode.
The recorder punches in
automatically at the
Auto Punch In point.
The recorder punches out
automatically at the
Auto Punch Out point.
Only track 3 in input monitoring,
and data will be recorded.
The RECORD LED lights up
in this area.
All tracks are in playback
monitoring mode.
REHEARSAL
TAKE
AUTO
PUNCH
