manualshive.com logo in svg

formlabs Fuse 1, Manual

Share
Download
formlabs Fuse 1 Manual Download Page 50

48

6.5 

Intermittent maintenance

Task

Frequency

Refer to

Section

Updating the firmware

When PreForm 

indicates a new 

firmware version 

is available.

Updating firmware

4.7

Replacing the optical 

cassette

After 100,000 layers 

printed or when the 

optical cassette is 

damaged

Replacing the optical 

cassette

6.5.2

Replacing the intake 

filter

After 120 full build 

volume prints or 2,400 

hours of printing, 

whichever comes first, 

or when the filter is 

damaged or cannot be 

sufficiently cleaned

Replacing the intake 

filter

6.5.3

Replacing the exhaust 

filter

After 120 full build 

volume prints or 2,400 

hours of printing, 

whichever comes first, 

or when the filter is 

damaged or cannot be 

sufficiently cleaned

Replacing the exhaust 

filter

6.5.4

Cleaning the upper laser 

window

After 1,000 hours 

of printing or if print 

quality indicates 

contaminated optics. 

Inspect the upper laser 

window after every 100 

hours of printing.

Cleaning the upper 

laser window

6.5.5

Cleaning the powder 

troughs

If powder becomes 

contaminated with 

fiber or other debris, 

or instructed to do 

so by Formlabs 

Support or a certified 

service provider.

Cleaning after a failed 

print

7.1

6.5.1 

Updating the firmware

For detailed guidance and visual assistance, visit 

support.formlabs.com

.

Formlabs regularly releases updated firmware to fix bugs and improve functionality. Review 
the PreForm and firmware release notes to learn more about the improvements that come 
with each version’s release. 

6.5.2 

Replacing the optical cassette

When disposing of a damaged optical cassette, remove it from the printer and clean off 
any lauralactum and powder following the instructions in section 

6.3.1 Cleaning the optical 

cassette

. Once cleaned, the filter can be disposed of with standard waste.

Summary of Contents for Fuse 1

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands