manualshive.com logo in svg

formlabs Fuse 1, Manual

Share
Download
formlabs Fuse 1 Manual Download Page 26

24

4.5 

Installing the machine

For detailed guidance and visual assistance, visit 

support.formlabs.com

.

After selecting a location, connect the printer to a power source to turn on the machine.

4.5.1 

Connecting the cables

Plug the included power cable into the power port on the back of the unit and connect the 
power cable to a dedicated circuit.

Files can be uploaded via Wi-Fi, Ethernet, or USB. For USB, connect the printer to a nearby 
computer. For Ethernet, connect the printer to your LAN. Refer to section 

4.6 Setting up a 

network connection

 for more information.

4.5.2 

Installing the Wi-Fi antenna

Install the Wi-Fi antenna to connect the machine to a wireless network.
To install the Wi-Fi antenna, screw the Wi-Fi antenna onto the jack on the back of the unit, next 
to the power, USB, and Ethernet ports.

4.5.3 

Turning on
To turn on the machine:

1.  Plug the included power cable into the power port on the back of the unit and connect the 

power cable to a dedicated circuit.

2.  Flip the breaker switch on the back of Fuse 1 to the ON position to turn on the machine.
3.  As the Fuse 1 initiates, the Formlabs logo with a progress bar appears on the touchscreen, followed 

by the onboarding process. Follow the on-screen prompts to finish setting up the machine.

To turn off the machine, refer to section 

6.6.3 Turning off

.

4.5.4 

Leveling

The printer must be completely level before printing can begin. If prompted, use a flat-head 
screwdriver to raise or lower each foot of the printer.

To level the machine:

1.  Turn on the printer. If necessary, the touchscreen prompts use of the leveling disc.

 °

The initial printer setup includes the leveling procedure.

2.  Follow the on-screen instructions to adjust the feet under the printer.
3.  The printer stand has a through hole under each of the printer’s feet. Insert a flat-head 

screwdriver through the hole and turn to adjust the corresponding foot.

Summary of Contents for Fuse 1

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands