manualshive.com logo in svg

formlabs Fuse 1, Manual

Share
Download
formlabs Fuse 1 Manual Download Page 32

30

To prepare the machine:

1.  Open the print enclosure door.
2.  Unplug and remove the build chamber.
3.  If you have the cardboard and foam optics protector that shipped in the optical cassette 

tray, remove the optical cassette.

4.  Using the vacuum attached to the Fuse Sift, vacuum the print enclosure and air filters.
5.  Close the air filter door and print enclosure door.
6.  Open the hopper. Scoop all powder out of the hopper using a clean, dry scoop. The 

powder can be reintroduced into your powder stream by running it through the sifter on 
the Fuse Sift.

Powder that comes into contact with fibers or other contaminants (e.g., in a vacuum 
cleaner) cannot be filtered and should be disposed of.Powder that comes into contact 
with fibers or other contaminants (e.g., in a vacuum cleaner) cannot be filtered and 
should be disposed of.

7.  Flip the breaker switch on the back of the unit to the 

OFF

 position to turn off the machine.

8.  Unplug all cables (power, Ethernet, and USB) from the back of the machine.
9.  Unscrew the Wi-Fi antenna from the back of the unit.

4.10.2 

Packaging

Thoroughly read and follow the instructions to properly package the machine. 
Skipping any of the following steps may result in shipping damage and void the 
warranty.

To package the machine:

1.  Open the air filter door and pull the door release to open the print enclosure door. Place 

the optics protector in the optical cassette tray with the foam side facing up. Close and 
secure the optical cassette tray. Close the print enclosure door.

2.  There is a platform on the pallet with holes that correspond to the printer’s feet. This platform 

is not centered on the pallet. Instead, it is closer to the left side of the pallet than the right, 
allowing room for the printer’s hopper. Place the pallet in front of the machine such that the 
right side of the pallet is aligned with the right side of the machine.

3.  Carefully tilt the machine backward. Have a partner slip the two lifting straps underneath 

the printer such that the handles are accessible on the left and right sides of the machine. 
Spread the lifting straps so that one is next to the rear feet of the machine and the other 
is next to the front feet.

Do not tilt the machine forward when placing the lifting straps. Doing so may damage 
the print enclosure door.

NOTICE

NOTICE

NOTICE

Summary of Contents for Fuse 1

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands