Ford 2010 F-250 Owner'S Manual Download Page 252 | Manualshive

Page: 252 / 408

background image

To calculate your maximum trailer weight:

For pickup trucks:

Take curb weight, hitch hardware and the driver’s

weight, then subtract them from the GCWR listed for your vehicle series,
engine, transmission and drive axle ratio

(refer to the chart/table in the

following text)

. This calculation will give you the maximum trailer

weight possible for your vehicle.

For chassis cabs and pickup trucks with aftermarket equipment:

Weigh your vehicle at a certified scale and subtract this actual curb
weight, hitch hardware, and the driver’s weight from the GCWR listed for
your vehicle series, engine, transmission and drive axle ratio

(refer to

the chart/table in the following text)

. This calculation will give you the

maximum trailer weight possible for your vehicle.

The weight of all additional cargo and passengers must be subtracted
from the maximum trailer weight calculated above.

Further trailer/hitch restrictions and limitations exist depending on the
type of trailer and hitch used. These additional maximum trailer weight
and tongue load limitations are listed in the chart/table that follows the
listing of GCWRs.

Towing a trailer places an additional load on your vehicle’s engine,
transmission, axle, brakes, tires and suspension. Inspect these
components carefully prior to and after any towing operation. Refer to

Transmission fluid temperature gauge

in the

Instrument Cluster

chapter for the transmission fluid temperature information.

Note:

Do not exceed the GCWR listed for your vehicle on the following

chart/table, or the GVWR, GAWR or tire ratings specified on the Tire
Label or Safety Compliance Certification Label.

WARNING:

Towing trailers beyond the maximum recommended

trailer weight which exceeds the limit of the vehicle’s GCWR,

GVWR, GAWR or tire ratings could result in engine damage,
transmission damage, structural damage, loss of vehicle control, vehicle
rollover and personal injury.

Tires, Wheels and Loading

252

2010 F-250/350/450/550

(f23)

Owners Guide, 2nd Printing
USA

(fus)

«
...
250
251
252
253
254
...
»

Summary of Contents for 2010 F-250

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 F-250

Brand: Calix Pages: 5

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

Brand: GMC Pages: 499

Brand: Kia Pages: 290

Brand: Edelbrock Pages: 1

Brand: FORM FIT Pages: 2

Brand: PEUGEOT Pages: 249

Brand: BMW Pages: 55

Brand: Whispbar Pages: 15

Brand: HAUL MASTER Pages: 8

Electra 225 1965

Brand: Buick Pages: 914

Brand: Warn Pages: 5

Brand: Xpresskit Pages: 18

Brand: Thule Pages: 3

Brand: Gator Pages: 6

Brand: F.lli Menabo Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands