Ford 1996 Aerostar Page 22 Manual Download | Manualshive

Page: 22 / 353

background image

20

*

[SR05600(ALL)06/95]

R

WARNING

When reinstalling a rear seat in your
vehicle it must be placed in its original
position. Improper installation of the seat
will prevent correct use of the safety belts
and could increase the risk of injury.
Refer to the warning label on the seat
belt.

*

[SR05700(ALL)03/95]

After installing the rear seat, make sure the
safety belt is not twisted before you insert it into
the detachable anchor. A twisted safety belt may
cause the retractor to not work properly. Then
insert the detachable anchor tongue into the
detachable anchor until you hear a “snap” and
feel the latch engage.

%

*

[SR06800(ALL)05/95]

Adjustable Lap Belts Without Retractors

[SR07000(ALL)06/95]

On the center seat of the rear three-passenger
seats you will find a lap-belt without a retractor.
You must adjust the lap belt to fit snugly and as
low as possible around your hips. Do not wear
the lap belt around your waist.

*

[SR07400(ALL)05/95]

one third page art:0020638-C

Fastening and unfastening occupant safety lap belts

File:03cpsra.ex

Update:Tue Aug 29 17:35:04 1995

«
...
20
21
22
23
24
...
»

Summary of Contents for 1996 Aerostar


































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 Aerostar

Brand: EAL Pages: 4

witty park XEV6 Series

Brand: hager Pages: 9

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

Brand: Ford Pages: 368

Brand: ICON Pages: 4

Brand: BraunAbility Pages: 46

Brand: Subaru Pages: 2

Brand: Chevrolet Pages: 324

2001 Accord Sedan

Brand: Honda Pages: 372

Brand: Imiola HAK-POL Pages: 3

viano 639 series

Brand: Mercedes-Benz Pages: 32

Brand: Rhino-Rack Pages: 5

Brand: AEV Pages: 16

Brand: FALCON RIDGE Pages: 8

RideControl 59540

Brand: Air Lift Pages: 10

Brand: Telwin Pages: 32

Brand: FALCON RIDGE Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands