Ford 1996 Aerostar Page 250 Manual Download | Manualshive

Page: 250 / 353

background image

272

%

*

[SV05580(ALL)04/95]

Cleaning the Engine

*

[SV05590(ALL)04/95]

A clean engine is more efficient because a
buildup of grease and dirt acts as an insulator,
keeping the engine warmer than usual.

*

[SV05592(ALL)07/95]

❑

Extreme care must be used if a power washer
is used to clean the engine. The high pressure
fluid could penetrate sealed parts and
assemblies causing damage or malfunctions.

[SV05594(ALL)08/95]

❑

In order to avoid possible cracking of the
engine block, do not spray a hot engine with
cold water.

[SV05596(ALL)06/95]

❑

The alternator and air intake must be
covered. Covering these components will help
prevent water damage.

*

[SV05598(ALL)04/95]

❑

Never wash or rinse the engine while it is
running. Water getting into the engine may
cause internal damage.

File:15cpsva.ex

Update:Tue Aug 29 17:51:51 1995

«
...
248
249
250
251
252
...
»

Summary of Contents for 1996 Aerostar


































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 Aerostar

Brand: ZAPTEC Pages: 240

Brand: UMBRA RIMORCHI Pages: 18

Brand: GARO Pages: 2

Brand: Porsche Pages: 192

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: Yescom Pages: 4

Brand: Z Automotive Pages: 16

Polaris TATOU 4S

Brand: Camoplast Pages: 13

Brand: Xhorse Pages: 48

Brand: v.link Pages: 21

Brand: ULTIMATE SPEED Pages: 32

Brand: Chevrolet Pages: 441

Brand: KEKO Pages: 13

Stealth 4191F Series

Brand: Road Armor Pages: 5

Brand: Saab Pages: 15

Magic Watch MWE-850-4DSM

Brand: Waeco Pages: 204

2917 Nstallation

Brand: Edelbrock Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands