Ford 1996 Aerostar Page 211 Manual Download | Manualshive

Page: 211 / 353

background image

231

*

[RE04300(ALL)01/95]

When you drive with the temporary spare tire,
DO NOT:

*

[RE04400(ALL)01/95]

❑

exceed 50 mph (80 km/h) under any
circumstances.

*

[RE04500(ALL)01/95]

❑

load your vehicle so that it is heavier than
the maximum vehicle load rating listed on
the tire decal.

*

[RE04600(ALL)01/95]

❑

tow a trailer.

*

[RE04700(ALL)01/95]

❑

use tire chains on this tire.

*

[RE04800(ALL)01/95]

❑

try to repair the temporary spare tire or
remove it from its wheel.

*

[RE04900(ALL)01/95]

❑

use the wheel for any other type of vehicle.

*

[RE05000(ALL)01/95]

❑

drive through an automatic car wash with
this tire. Because the temporary spare tire is
smaller than a conventional tire, it reduces
the ground clearance. Your vehicle may get
caught in the rails and it could be damaged.

%

*

[RE05100(ALL)03/95]

Spare Tire Location

[RE05200(ALL)03/95]

If your vehicle is a standard length van model,
the spare tire is mounted inside a carrier at the
left rear quarter panel. To remove the spare tire,
remove the wing nut and plate. A flat tire can
be temporarily stowed in the same location.

[RE05300(ALL)01/89]

quarter page art:0020264-A

A side mounted spare tire

File:12cprea.ex

Update:Tue Aug 29 17:46:27 1995

«
...
209
210
211
212
213
...
»

Summary of Contents for 1996 Aerostar


































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 Aerostar

Brand: CAMPARK Pages: 20

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 2

BT150 - Headset - Over-the-ear

Brand: Jabra Pages: 2

Brand: Roav Pages: 10

Brand: Cadillac Pages: 20

Vehicle Asset Communicator

Brand: I.D. Systems Pages: 41

Brand: EUFAB Pages: 4

EPS-LD SafePark

Brand: Tobe Pages: 2

Brand: Whispbar Pages: 77

Brand: Audi Pages: 4

Brand: Thule Pages: 15

Brand: Rugged Ridge Pages: 3

LockNLoad LightenUp

Brand: Yakima Pages: 13

Brand: Honda Pages: 234

Brand: OCAM Pages: 4

Brand: Chevrolet Pages: 349

Brand: Toyota Pages: 31

Brand: Mitsubishi Pages: 722

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands