manualshive.com logo in svg

Ford 1996 Aerostar, Manual, Page: 183 / 353

Share
Download
Ford 1996 Aerostar Manual Download Page 183

202

*

[DR27850(ALL)11/89]

Rocking the vehicle

*

[DR27950(ALL)05/95]

If your vehicle gets stuck (for example, in mud
or snow), you may rock it out of the spot. Shift
in a steady rhythm between forward and reverse
gears. Allow the transmission to fully engage,
then press lightly on the accelerator. Do not rock
the vehicle for more than a few minutes. This
may overheat the engine and transmission,
causing damage to both. In addition, other
vehicle systems and components may also be
damaged.

*

[DR27975(ALL)05/95]

R

WARNING

Do not spin the wheels at over 35 mph
(55 km/h). The tires may fail and injure a
passenger or bystander.

%

*

[DR28050(ALL)03/95]

Driving With a Heavy Load

*

[DR28101(ALL)01/95]

There are limits to the amount of weight your
vehicle can carry or tow. The total weight of
your vehicle, plus the weight of the passengers
and cargo, should never be more than the Gross
Vehicle Weight Rating (GVWR). Also, the weight
that your vehicle carries over the front axle and
rear axle should never be more than the Gross
Axle Weight Rating (GAWR) for the respective
axle.

*

[DR28150(ALL)08/95]

The weight limits of your vehicle’s tires affect
the GVWR or GAWR limitations. Usage of
replacement tires with higher weight limits than
originals does not increase GVWR or GAWR.
Usage of lower capacity replacement tires may
lower GVWR and GAWR limitations.

File:10cpdra.ex

Update:Tue Aug 29 17:45:28 1995

Summary of Contents for 1996 Aerostar


































































































































































































































































































































































Reviews:

No comments