Ford 1996 Aerostar Page 311 Manual Download | Manualshive

Page: 311 / 353

background image

333

driving to complete the check” of the OBD II
system. As soon as all of the OBD II system
checks are successfully completed, the OBD II
system is set to the ready condition. The amount
of driving required to reach the ready condition
varies with individual driving patterns. To
complete this requirement in the minimum
amount of time, refer to the OBD II Drive Cycle
defined below. If the vehicle owner cannot or
does not want to do the additional driving
required by law, a service center can perform
this drive cycle as it would any other type of
repair work.

*

[SV50030(ALL)07/95]

OBD II Drive Cycle

*

[SV50040(ALL)06/95]

The following steps must be run in the order
shown. If any steps are interrupted, repeat the
preceding step. Any safe driving mode is
acceptable between steps.

*

[SV50050(ALL)06/95]

Always drive vehicle in safe manner according
to traffic conditions and obey all traffic laws.

[SV50055(ALL)08/95]

NOTE: When instructions read “in drive,” use

the standard Overdrive gear. It is not
necessary to turn Overdrive off with
the OVERDRIVE OFF button. For more
information on Overdrive, refer to the
Automatic Overdrive Transmission
section of the

Driving Your Aerostar

chapter.

*

[SV50060(ALL)07/95]

The engine must be warmed up and at
operating temperature before proceeding with
the drive modes of the following OBD II Drive
Cycle.

*

[SV50070(ALL)06/95]

1.

Start the engine. Drive or idle (in neutral)
the vehicle for 4 minutes.

*

[SV50080(ALL)06/95]

2.

Idle the vehicle in drive for 40 seconds.

*

[SV50090(ALL)07/95]

3.

Accelerate the vehicle to 45 mph (70 km/h)
at 1/4 to 1/2 throttle for 10 seconds.

File:15cpsva.ex

Update:Tue Aug 29 17:51:51 1995

«
...
309
310
311
312
313
...
»

Summary of Contents for 1996 Aerostar


































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 Aerostar

Brand: PAC Pages: 15

Brand: DANA Pages: 42

Brand: dallara Pages: 37

Brand: Yakima Pages: 8

Brand: Kia Pages: 10

Brand: BGS technic Pages: 5

Brand: Oldsmobile Pages: 344

Brand: ABL Pages: 66

2012 Truck Chassis cab

Brand: RAM Pages: 506

Brand: Nuna Pages: 17

Brand: Mercedes-Benz Pages: 358

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: Draw tite Pages: 4

CF-UFORCE-DRW01

Brand: FALCON RIDGE Pages: 6

Brand: GROM Audio Pages: 20

Brand: Prorack Pages: 13

Prestige 128-8602

Brand: Audiovox Pages: 8

Brand: Ford Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands