Ford 1996 Aerostar Page 305 Manual Download

Page: 305 / 353

327

[SV47381(ALL)06/95]

half page art:0095018-A

Replacing the high-mount brakelamp bulb — liftgate
models only

[SV47383(ALL)05/94]

Dual Rear Door Models

[SV47384(ALL)03/95]

To remove the brakelamp:

[SV47385(ALL)03/93]

Remove the two screws from the surface of
the lens.

[SV47386(ALL)03/93]

Pull the lens assembly out of the lamp
housing.

[SV47387(ALL)03/93]

Pull the bulb socket out of the lens assembly.
It is not necessary to twist the socket.

[SV47388(ALL)03/93]

Pull the bulb out of the socket.

File:15cpsva.ex

Update:Tue Aug 29 17:51:51 1995

Summary of Contents for 1996 Aerostar


































































































































































































































































































































































Search results

Summary of Contents for 1996 Aerostar

Reviews:

Related manuals for 1996 Aerostar

Brands by name

Popular brands

Ford 1996 Aerostar, Manual

Search results

Summary of Contents for 1996 Aerostar

Reviews:

Related manuals for 1996 Aerostar

Brands by name

Popular brands