background image

- The total wiring interconnecting equipment in one line must not exceed 100 m. To avoid interference in

the line, it is advisable to place a line terminator as the last element in the chain. This consists in a 120 Ω
resistance  between  terminal  2  and  3  on  the  XLR  DMX  OUT  connector  on  the  last  element.  See  the
following diagram:

- Connect the equipment to the mains and switch it on.

GENERAL SAFETY RECOMMENDATIONS

- Do not open the equipment under any circumstances. 

- Make sure that the devices are at least 50 cm from inflammable substances or elements. 

- Do not look at the laser beams from a distance of less than 15 cm or for more than 10 seconds of direct

radiation, to avoid serious damage to eyes. 

- Switch the equipment off for 15 minutes every 2 hours to avoid overheating. 

- Do not continually switch the equipment on and off as this could decrease its useful life.

- Only use this equipment in covered and refrigerated spaces.

- Do not move or manipulate the equipment while it is connected to the mains and operating.

- Do not modify the lighting elements of the equipment without technical supervision or with material that

has not been guaranteed by the supplier.

TECHNICAL SPECIFICATIONS

DMX-81

CHARACTERISTICS

192-channel DMX 512 control console.
12 accesses to up to 16 channels.
8 sliding controls assignable to channels 1 to 8 or 9 to 16 for each access.
6 chase presets each with 240 programmable scenes.
240 scenes divided into 30 memory banks of 8 scenes each.
Automatic programmable sequencing controlled by speed and time faders.
Manual,  automatic  control  or  sound  activation  thanks  to  integrated
microphone.
Blackout function.

OUTPUTS

DMX OUT, male 3-pin XLR

POWER SUPPLY

9 V DC, 1 A with adapter included

DIMENSIONS

482 x 132 x 73 mm depth. 3 U 19" rack

- 14 -

EN

Summary of Contents for DMX-81

















Reviews: