background image

ADDING A SCENE TO A SPECIFIC STEP IN A CHASE

- Hold down the PROGRAM button for 3 seconds to access the programming mode. The LED PROGRAM

indicator will flash constantly.

- Select the chase to be edited using the CHASE 1-6 buttons.

-  Press the TAPSYNC/DISPLAY button and the total number of scenes will appear on the display.

- Find the required position for the new scene using the BANK UP and BANK DOWN buttons.

-  Press the MIDI/ADD button to add a blank scene where the new scene will be stored.

- Select the bank where the scene is that you wish to add to the chase using the BANK UP and BANK DOWN

buttons. 

-  Press  the  corresponding  SCENES  1-8  scene  and  then  press  the  MIDI/ADD  button  to  store  the

programming. All the LED indicators will flash 3 times to show that it has been programmed correctly. 

- Repeat the previous steps to add all the scenes you wish to the chase.

- Press  and  hold  the  PROGRAM  button  for  3  seconds  to  exit  the  programming  mode  and  press  the

BLACKOUT button to activate the output channels again.

Example

: to store the new scene between two specific positions, for example between 5 and 6, you have

to press the MIDI/ADD button when the display shows scene 005. On pressing this button, the display will
show the number of the empty scene, increasing it one unit, so in our case it will say 006, showing that the
empty scene has been created afterwards and between positions 5 and 6.

ADDING A BANK TO THE END OF A CHASE

- Hold down the PROGRAM button for 3 seconds to access the programming mode. The LED PROGRAM

indicator will flash constantly.

- Select the chase that you wish to edit using the CHASE 1-6 buttons.

- Select the bank that you wish to add to the chase using the BANK UP and BANK DOWN buttons. Take into

account that the 8 scenes from the bank will be stored at the end of the current chase programming.

Press the MUSIC/BANK COPY button to make a copy of the bank. 

-  Press the MIDI/ADD button to store the programming in the chase. All the LED indicators will flash 3 times

to show that it has been programmed correctly.

- Repeat the previous steps to add all the banks you wish to the chase.

- Press  and  hold  the  PROGRAM  button  for  3  seconds  to  exit  the  programming  mode  and  press  the

BLACKOUT button to activate the output channels again.

DELETING A SCENE FROM A CHASE

- Hold down the PROGRAM button for 3 seconds to access the programming mode. The LED PROGRAM

indicator will flash constantly.

- Select the chase that you wish to edit with the CHASE 1-6 buttons.

-  Press the TAPSYNC/DISPLAY button and the total number of scenes will appear on the display.

- Find the scene to be deleted using the BANK UP and BANK DOWN buttons.

-  Press the AUTO/DEL button to delete the scene. All the LED indicators will flash 3 times to show that the

scene has been deleted correctly. 

- Repeat the previous steps to delete as many scenes as you wish.

- Press  and  hold  the  PROGRAM  button  for  3  seconds  to  exit  the  programming  mode  and  press  the

BLACKOUT button to activate the output channels again.

- 10 -

EN

Summary of Contents for DMX-81

















Reviews: