Flying Voice FGW4148-16S User Manual Download Page 50

Page: 50 / 78

Chapter 4 Web Interface

FGW4148-16S/32S/48S User Manual

FXS Settings

Basic

Set the basic information provided by your VOIP Service Provider, such as Phone Number, Account, password, SIP
Proxy and others.

Table 24

Line

Field Name

Description

Line Enable

Enable/Disable the line.

Outgoing Call without
Registration

Enable/Disable Outgoing Call without Registration

If enabled, SIP-1 will not send register request to SIP server; but in Status/ SIP
Account Status webpage, Status is Registered; lines 1 can dial out, but the
external line number cannot dialed line1.

Proxy Server

The IP address or the domain of SIP Server

Outbound Server

The IP address or the domain of Outbound Server

Backup Outbound Server

The IP address or the domain of Backup Outbound Server

Proxy port

SIP Service port, default is 5060

Outbound Port

Outbound Proxy

’

s Service port, default is 5060

Backup Outbound Port

Backup Outbound Proxy

’

s Service port, default is 5060

Display Name

The number will be displayed on LCD

Phone Number

Enter telephone number provided by SIP Proxy

Account

Enter SIP account provided by SIP Proxy

Summary of Contents for FGW4148-16S















































































Search results

Summary of Contents for FGW4148-16S

Reviews:

Related manuals for FGW4148-16S

Brands by name

Popular brands

Flying Voice FGW4148-16S, User Manual

Search results

Summary of Contents for FGW4148-16S

Reviews:

Related manuals for FGW4148-16S

Brands by name

Popular brands