Flying Voice FGW4148-16S User Manual Download Page 15

Page: 15 / 78

Chapter 1 Product description

FGW4148-16S/32S/48S User Manual

FGW4148-32S

Table 4

FGW4148-32S Front panel

Table 5

FGW4148-32S Rear panel

AC 100~220V

Connector for a power adapter.

LED/Interface

Status

Description

LED

LED Screen

The screen will appear the information about the device
On(Green)

The router is powered on and running normally.

Off

The router is powered off.

Blinking(Green)

The router is updating

The router is running normally.

When the light is on, it indicates system applications occured

以太网接口指示灯

Blinking(Green)

Have data transmission

The system is not powered on or the network port is not

connected to the network device

Interface

Page up

，

can view info of FXS status.

使用

键返回待机页面

Press it to restore factory settings above 5S

LAN

Connector for local network devices

WAN

Connector for accessing the internet

PHONE 1-16

Connect to the phone

Interface

Description

32-26 PHONE

Transfer interface for 26-32 FXS

25-1 PHONE

Transfer interface for 1-26 FXS

CONSOLE

Serial port,used to connect to your PC

Ground

Connect the ground wire

Summary of Contents for FGW4148-16S















































































Search results

Summary of Contents for FGW4148-16S

Reviews:

Related manuals for FGW4148-16S

Brands by name

Popular brands

Flying Voice FGW4148-16S, User Manual

Search results

Summary of Contents for FGW4148-16S

Reviews:

Related manuals for FGW4148-16S

Brands by name

Popular brands