Flying Voice FGW4148-16S User Manual Download Page 45

Page: 45 / 78

Chapter 4 Web Interface

FGW4148-16S/32S/48S User Manual

Table 18

L2TP

Parameters name

Description

VPN Enable

Whether to enable VPN.

Select PPTP mode.

Initial Service IP

The IP address of the VPN server.

User Name

The user name required for authentication.

Password

The password required for authentication.

VPN As Default Route

Prohibited or open, the default is prohibited.

MPPE Stateful
Require MPPE

Parameters name

Description

VPN Enable

Whether to enable VPN.

Select PPTP mode.

Initial Service IP

The IP address of the VPN server.

User Name

The user name required for authentication.

Password

The password required for authentication.

L2TP Tunnel Name

L2TP Tunnel Password

VPN As Default Route

Prohibited or open, the default is prohibited.

Summary of Contents for FGW4148-16S















































































Search results

Summary of Contents for FGW4148-16S

Reviews:

Related manuals for FGW4148-16S

Brands by name

Popular brands

Flying Voice FGW4148-16S, User Manual

Search results

Summary of Contents for FGW4148-16S

Reviews:

Related manuals for FGW4148-16S

Brands by name

Popular brands