Flying Voice FGW4148-16S User Manual Download Page 70

Page: 70 / 78

Chapter 4 Web Interface

FGW4148-16S/32S/48S User Manual

Field Name

Description

Provision Enable

Enable provision or not.

Resync on Reset

Enable resync after restart or not

Resync Random

Set the maximum delay for the request of synchronization file. The default is 40

Resync Periodic(sec)

If the last resync was failure, The router will retry resync after the

“

Resync Error

Resync Error Retry

Set the periodic time for resync, default is 3600s

Forced Resync

If it

’

s time to resync, but the device is busy now, in this case,the router will

Resync After

Enable firmware upgrade after resync or not. The default is Enabled

Resync From SIP

Enable/Disable resync from SIP

Option 66

It is used for In-house provision mode only. When use TFTP with option 66 to

Config File Name

It is used for In-house provision mode only. When use TFTP with option 66 to

Profile Rule

URL of profile provision file
Note that the specified file path is relative to the TFTP server

’

s virtual

Table 47

Firmware Upgrade

Field Name

Description

Upgrade Enable

Enable firmware upgrade via provision or not

Upgrade Error Retry
Delay(sec)

If the last upgrade fails, the router will try upgrading

again after

“

Upgrade Error Retry Delay

”

period, default is 3600s

Upgrade Rule

URL of upgrade file

Summary of Contents for FGW4148-16S















































































Search results

Summary of Contents for FGW4148-16S

Reviews:

Related manuals for FGW4148-16S

Brands by name

Popular brands

Flying Voice FGW4148-16S, User Manual

Search results

Summary of Contents for FGW4148-16S

Reviews:

Related manuals for FGW4148-16S

Brands by name

Popular brands