FLIR
LEPTON® Engineering Datasheet
The information contained herein does not contain technology as defined by the EAR, 15 CFR 772, is publicly available,
and therefore, not subject to EAR. NSR (6/14/2018).
Information on this page is subject to change without notice.
Lepton Engineering Datasheet, Document Number: 500-0659-00-09 Rev: 203
84
© FLIR Commercial Systems, 2014. All rights reserved worldwide. No parts of this manual, in whole or in part, may be
copied, photocopied, translated, or transmitted to any electronic medium or machine readable form without the prior written
permission of FLIR Commercial Systems
Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR Commercial Systems
and/or its subsidiaries. All other trademarks, trade names or company names referenced herein are used for identification only and
a r e the property of their respective owners.
This product is protected by patents, design patents, patents pending, or design patents pending.
If you have questions that are not covered in this manual, or need service, contact FLIR Commercial Systems Customer Support
at 805.964.9797 for additional information prior to returning a camera.
This documentation and the requirements specified herein are subject to change without notice.
This equipment must be disposed of as electronic waste.
Contact your nearest FLIR Commercial Systems, Inc. representative for instructions on how to return the product to
FLIR for proper disposal.
FCC Notice.
This device is a subassembly designed for incorporation into other products in order to provide an infrared camera function. It is not an
end-product fit fo1r consumer use. When incorporated into a host device, the end-product will generate, use, and radiate radio frequency energy that
may cause radio interference. As such, the end-product incorporating this subassembly must be tested and approved under the rules of the Federal
Communications Commission (FCC) before the end-product may be offered for sale or lease, advertised, imported, sold, or leased in the United
States. The FCC regulations are designed to provide reasonable protection against interference to radio communications. See 47 C.F.R. §§ 2.803
and 15.1 et seq.
Industry Canada Notice.
This device is a subassembly designed for incorporation into other products in order to provide an infrared camera
function. It is not an end-product fit for consumer use. When incorporated into a host device, the end-product will generate, use, and radiate radio
frequency energy that may cause radio interference. As such, the end-product incorporating this subassembly must be tested for compliance with
the Interference-Causing Equipment Standard, Digital Apparatus, ICES-003, of Industry Canada before the product incorporating this device may
be: manufactured or offered for sale or lease, imported, distributed, sold, or leased in Canada.
Avis d
’Industrie Canada.
Cet appareil est un sous-ensemble conçu pour être intégré à un autre produit afin de fournir une fonction de caméra
infrarouge. Ce n
’est pas un produit final destiné aux consommateurs. Une fois intégré à un dispositif hôte, le produit final va générer, utiliser et
émettre de
l’énergie radiofréquence qui pourrait provoquer de l’interférence radio. En tant que tel, le produit final intégrant ce sous-ensemble doit
être testé pour en vérifier la conformité avec la Norme sur le matériel brouilleur pour les appareils numériques (NMB-003)
d’Industrie Canada avant
que le produit intégrant ce dispositif puisse être fabriqué, mis en vente ou en location, importé, distribué, vendu ou loué au Canada.
EU Notice.
This device is a subassembly or component intended only for product evaluation, development or incorporation into other products in
order to provide an infrared camera function. It is not a finished end-product fit for general consumer use. Persons handling this device must have
appropriate electronics training and observe good engineering practice standards. As such, this product does not fall within the scope of the
European Union (EU) directives regarding electromagnetic compatibility (EMC). Any end-product intended for general consumer use that
incorporates this device must be tested in accordance and comply with all applicable EU EMC and other relevant directives.
