background image

427-0064-00-12 Version 100

August 2017

11

1

Camera Installation

1.4.4

Alarm Connections—Not supported

1.4.5

Ethernet

Connect a shielded Cat5e or Cat6 Ethernet cable to the RJ-45 jack. If using PoE to supply power to 
the camera, connect the other end of the cable to a PoE switch or PoE injector. Otherwise connect 
the cable to a network switch.

1.4.6

Camera Grounding

Ensure the camera is properly grounded. Failure to properly ground the camera can lead to 
permanent damage to the camera. Typical to good grounding practices, the camera chassis ground 
should be connected to the lowest resistance path possible. 

1.5

Mounting the Camera

1. Place the supplied template where you will install the 

camera. Mark the position of the two screw holes for the 
base of the mounting bracket.

2. At the center of the template, a cable entry hole 40 mm 

(1.57”) in diameter will provide for hidden cables.

3. Drill the cable entry hole for cables or use the slot for 

surface mounting the cables. 

4. Drill holes slightly smaller than the supplied plastic screw 

anchor on each marked screw hole. 

5. Insert the plastic screw anchors into the drilled holes.
6. Connect the camera cables and thread them through the 

cable entry hole. Refer to 

Camera Connections, pg. 9

 for cable connections. 

7. Match the mounting slots of the camera with the plastic screw anchors at the installation location.
8. Fasten the camera with the supplied M4 screws.
9. Loosen the set screws in order to manipulate the 

camera positioning at the ball joint. The camera can be 
rotated, twisted, and pointed up or down at the ball joint.

10.  Point the camera in the desired direction and fasten the 

screws.

M4 mounting

slots

Slot for surface
mounting

cable

Ball-joint

set screws

Base

set screw

Summary of Contents for FB-Series O




































Reviews: