Fisher & Paykel HD30 Installation Instructions Manual Download Page 20

Page: 20 / 22

Remote Blower Electrical Connection

• Remove the cover from the remote blower, then remove the wiring box cover.

• Pull the electrical wiring through the hole in the blower base and secure it according to local codes using

a suitable UL listed strain relief or conduit fitting (not included).

• Connect the N (neutral) wire to the white wire in the wiring box with twist-on connector Fig.21.

• Connect the L1 (live) wire to the black wire in the wiring box with twist-on connector Fig.21.

• Connect the green power supply ground wire to the green ground screw.

Verify that the main filter, flap and wiring box cover are positioned correctly with wiring clearance.

• Replace the wiring box cover and screws taking care not to pinch the wiring under the wiring box cover.

• Reinstall the remote blower cover.

Fig.21

https://producthelp.fisherpaykel.com/us/Cook/Ventilation/Downdraft/HD36/User_Guide_HD36/05_installation_instructions

Updated: Fri, 28 Jun 2019 03:30:59 GMT

Summary of Contents for HD30























Search results

Summary of Contents for HD30

Reviews:

Related manuals for HD30

Brands by name

Popular brands

Fisher & Paykel HD30, Installation Instructions Manual

Search results

Summary of Contents for HD30

Reviews:

Related manuals for HD30

Brands by name

Popular brands