Fisher & Paykel HD30 Installation Instructions Manual Download Page 4 | Manualshive

Page: 4 / 22

background image

Product Dimensions

Remote blower (HBD1200E)

Downdraft unit and internal blower box (HBD600I) which can

also be mounted on the back of the appliance

Remote blower connection plate (can also be

mounted on the back of appliance)

Product Dimensions

HD30

inches (mm)

HD36

inches (mm)

A.

Top trim width

30” (762)

36” (914)

B.

Width of product

27” (686)

33” (838)

C.

Minimum distance to rear of the cabinet or wall

1” (25)

1” (25)

https://producthelp.fisherpaykel.com/us/Cook/Ventilation/Downdraft/HD36/User_Guide_HD36/05_installation_instructions

Updated: Fri, 28 Jun 2019 03:30:59 GMT

Powered by

4

«
...
2
3
4
5
6
...
»

Summary of Contents for HD30























Reviews:

No comments

Related manuals for HD30

Brand: HAMPTON BAY Pages: 30

Brand: ebm-papst Pages: 7

Brand: ebm-papst Pages: 11

Brand: M.K.Plastics Pages: 12

Brand: Flex Pages: 120

Grease Viper Series

Brand: Trion Pages: 16

Brand: Maico Pages: 32

Brand: Lindab Pages: 4

Brand: ebm-papst Pages: 6

Brand: Paris Rhone Pages: 21

TD-SILENT Series

Brand: S&P Pages: 52

Brand: Adler Europe Pages: 52

KORASMART TUBE 2400

Brand: KORADO Pages: 96

Brand: NuTone Pages: 2

Brand: ebm-papst Pages: 12

Brand: Mylek Pages: 7

Brand: Vortice Pages: 80

Brand: ELECTROTEK Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands