background image

 

3

£

DESCRIPTION OF FIREYE D-30 SYSTEM COMPONENTS

Control

Part Numbers

Control Chassis and Cover

70D30

Plug-in Program Module

71D81-15 Second purge
71D80-30 Second purge
71D90-90 Second purge

Plug-in Amplifier module 
and Flame Scanner

Amplifier

Flame Scanner

72DRT1
Rectification

69ND1-1000K4  1/2" mount - 12" flamerod
69ND1-1000K6  1/2" mount - 18" flamerod
69ND1-1000K8  1/2" mount - 24" flamerod

72D1R1 infra-red (IR) AUTOCHECK
71DIR3 for specific applications (see note below)

48PT2-1003

1/2" straight mount 96" cable

48PT2-9003

1/2" angle  mount 96" cable

48PT2-1007

1/2" straight mount 48" cable

48PT2-9007

1/2" angle mount 48" cable

72DUV1
Ultraviolet (UV)

UV1A3

    1/2" mount 36" cable

UV1A6

    1/2" mount 72" cable

UV2

    3/8" mount 36" cable

UV8A

      90

q

 head 1/2" NPT mount, 

 72" unshielded leads.

UV90-3, -6, -9    90

º

 side opening, 36”    

                              (900mm), 72" (1800mm),
                              or 108" (2700mm) cable
45UV3-1050

   3/4” mount, cast aluminum

 housing, 8’ wire.

72DUVS4: Ultraviolet Repetitive Self-Check 2-4 sec. FFRT.
72DUVS1T: Ultraviolet Repetitive Self-check 1 sec. FFRT.

45UV5-1009 

  1" mount, 72" wire leads

Wiring Base

60-1386-2

Standard base for surface mounting

60-1466-2

Open base for cabinet mounting.

NOTE:

 Infra-red “Autocheck” amplifier module 72D1R3 may be specified for burner applications firing special fuel such as sawdust, 

sander dust, low BTU gas. 

The 72D1R3 is not to be used on any liquid fuel fired burner since it may result in malfunctions causing 
damage to property and/or injury to personnel. 

Plug-in Module Retainer

Test Jack Black (-)

Plug-in Flame Amplifier

Cover Retainer

LED Indicators

Test Jack Red (+) 

Chassis Retaining Screw

Check-Run Test Switch

Lock-out Switch

Plug-in Programmer

Summary of Contents for D30 Series

























Reviews: