Firegear OFP-L36TFS-N Installation And Operating Instructions Manual Download

Page: 3 / 33

REV. 1-5-17 Page 2

Kalea Bay Outdoor Fireplace

1. This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases.

2. Do not place Propane (LP) supply tanks inside any

structure. Locate propane tanks outdoors.

3. This fireplace is to be used only outdoors in a well

ventilated space and shall not be used in a building,

garage, or any other enclosed area.

4. Do not use this fireplace as a wood burning fireplace.

Use only high temperature media approved for use with

this fireplace.

5. Do not use this fireplace to cook or burn paper or other

objects.

6. Do not use if exposed to or under water. Immediately

call a qualified service technician to inspect the

fireplace and replace any part of the control system

and any gas control which has been under water.

7. Turn fireplace OFF and let cool before servicing. Only

a qualified service person should service and perform

service.

8. To prevent performance problems in Propane (LP)

fireplaces, do not use a Propane tank less than 100lbs.

capacity.

SAFETY

COMMONWEALTH OF MASSACHUSETTS

REQUIREMENTS

These appliances are approved for installation in the US

state of Massachusetts if the follow additional requirements

are met:

• Un-vented Room Heaters shall be installed in

accordance with 527 CMR 30.

• Installation and repair must be done by a plumber

or gas fitter licensed in the Commonwealth of

Massachusetts.

• The flexible gas line connector used shall not exceed

36-inches (92 centimeters) in length.

• The individual manual shut-off must be a T-handle type

valve.

• Unvented appliances may NOT be installed in bed-

rooms or bathrooms.

• A working smoke detector must be installed in the area

where vent-free appliances are installed.

Seller of of unvented Propane or Natural gas-fired

supplemental room heaters shall provide to each purchaser

a copy of 527 CMR 30 upon sale of the unit.

State of Massachusetts: The installation must be made

by a licensed plumber or gas fitter in the Commonwealth

of Massachusetts.

Sellers of unvented Propane or Natural gas-fired supple-

mental room heaters shall provide to each purchaser a

copy of 527 CMR 30 upon sale.

Vent-free gas products are prohibited for bedroom or

bathroom installation in the Commonwealth of

Massachusetts.

CERTIFICATION:

The Kalea Bay Outdoor fireplaces are

tested and approved to ANSI Z21.97-2014, CSA 2.41-2014

standards by Underwriters Laboratories using listing

MH#60069. It should be installed by a qualified installer in

accordance with local and state building codes using

National Fuel Gas Code ANSI Z223.1/NFPA54 or current

CSA-B149.1 installation codes for Gas Burning Appliances

and Equipment in Canada.

DESCRIPTION:

These Outdoor fireplace models come

pre-programmed and ready to operate with HI/LO

capibilitties once installation is complete. They use an

electronic ignition that runs off of (4) AA batteries or an

optional adapter (AF-4000ADP24). These are radiant

fireplaces only and do not have a fan option.

Do not

burn real wood or other combustible materials in these

fireplaces.

Use only approved glass media. Each model

is available for Natural or Propane gas and must be

ordered accordingly. They are not field convertible. There

is no venting required for this fireplace. Provide adequate

clearances according to this manual and cross ventilation.

The burner assembly is removable for service. NEVER

obstruct the front opening(s) of the fireplace.

NOTE:

This fireplace comes with (4) metal standoffs

attached (flat) secured to the top of the firebox. These

are to be used if combustible materials are being used as

part of the installation. If all non-combustible materials are

being used for the installation then the standoffs are not

required for installation.

LOCAL CODES

Install and use fireplace with care. Follow all local codes.

In the absence of local codes, use the latest edition of the

National Fuel Gas Code ANSI Z223.1/ NFPA54.

Available from:

American National Standards Institute, Inc.

25 West 43rd Street, 4th floor

New York, NY 10036

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02169-7471

Summary of Contents for OFP-L36TFS-N


































Search results

Summary of Contents for OFP-L36TFS-N

Reviews:

Related manuals for OFP-L36TFS-N

Brands by name

Popular brands

Firegear OFP-L36TFS-N, Installation And Operating Instructions Manual

Search results

Summary of Contents for OFP-L36TFS-N

Reviews:

Related manuals for OFP-L36TFS-N

Brands by name

Popular brands