Firegear ANF-L48 Page 2 Instructions Manual Download

Page: 2 / 14

AnF Enclosures

REV. 8-29-18 Page 2

Contents of Enclosure

Each quarter section has a 90-degree inner ﬂ ange on one side (See Fig. 2 - arrows). Butt the inner

ﬂ ange of one other quarter section to the non-ﬂ ange side of another section (See Fig 3).

(4) Quarter Sections

(4) 45° Pan Supports

Fig. 1

Round

AnF Contents

(4) MgO Boards

(1) Vent-Kit-6x12

Round AnF Enclosure Assembly

Two people are recommended to assemble all enclosures. It is also recommended to assemble the

enclosure on a ﬂ at surface. The assembly of the AnF should be done at or near the location of the

installation.

Leveling Legs

(16) Self Tapping Screws (16) Cement Board Screws

AnF-R42 & AnF-R48: 4 Legs

AnF-R60: 8 Legs

STEP 1

Remove all parts and make sure that you have received all necessary pieces.

It is important to start the assembly process with the quarter sections upside-down. To make sure the

quarter pieces are upside down, the bottom side has a nutsert (See Fig 2 - circle).

The nutsert needs

to be facing upward on each quarter section.

Fig. 2

N 90° Flange

Fig. 3

Lining Up Sides

*ANF-R42 and ANF-48 ONLY!

(2) Horizontal Pan Supports

*ANF-60 ONLY!

NOTE

Summary of Contents for ANF-L48















Search results

Summary of Contents for ANF-L48

Reviews:

Related manuals for ANF-L48

Brands by name

Popular brands

Firegear ANF-L48, Instructions Manual

Search results

Summary of Contents for ANF-L48

Reviews:

Related manuals for ANF-L48

Brands by name

Popular brands