background image

AnF Enclosures

REV. 8-29-18  Page 14

Skytech Products Group (Firegear Outdoors) hereby 

warrants to the end user that products will be free from 

material and workmanship defects that prevent safe and 

correct operation of the product. The warranty 

commences from date of sale to the end user for the 

following period:

Stainless Steel Components

5-Years

Gas Valve, Spark Ignitor & 

Electronic Parts

2-Years

G90 Galvanized Pans

3-Years

Gas Logs

5-Years

Glass Windshield

1-Year

Glass Media

5-Years

Remote Controls

5-Years

AnF Enclosure

5-Years

Lava Rock & Lava Stones

No Warranty

Consumer/Non-Commercial Applications

Stainless Steel Components

1-Year

Gas Valve, Spark Ignitor & 

Electronic Parts

1-Year

G90 Galvanized Pans

1-Year

Gas Logs

1-Year

Glass Windshield

1-Year

Glass Media

1-Year

Remote Controls

1-Year

AnF Enclosure

1-Year

Lava Rock & Lava Stones

No Warranty

Commercial Applications

End User must provide a bill of sale, canceled check, or 

payment record from the end user to verify 

purchase date and to establish warranty period. This 

Limited Warranty shall be valid and limited to the 

original purchaser only.

WARNING:

 Any modification to the product will void the 

warranty.

This Limited Warranty shall be limited to the repair and/

or replacement of parts that have proven to be defective 

under normal use and service. Before 

returning any parts, contact our Technical Service 

Department for a Return Materials Authorization (RMA) 

number.  All warranty claims must be made by the OEM 

/ Distributor / Dealer account on behalf of the end user.  

You may contact Technical Service at (855) 498-8324.

All approved returned defects must be confirmed by our 

Technical Service Department.  If the defect is confirmed 

and we approve the claim, we will replace such parts 

without charge.  This warranty gives you specific legal 

rights, and you may also have other rights, which vary 

from state to state.

Travel, diagnostic cost, service labor to repair the 

defect and freight charges on warranty parts to and from 

the factory will be responsibility of the owner. We will not 

be responsible for labor charges and/or 

damage incurred in installation, repair, and 

replacement. 

This Limited Warranty is voided if not assembled, 

installed and operated as intended. This Limited 

Warranty does not cover any defects due to accident, 

abuse, misuse, alteration, misapplication, vandalism, 

improper installation or improper maintenance or 

service, removal from the original location or 

re-installation into another location, or failure to 

perform normal and routine maintenance.

Damage due to severe weather conditions such as hail, 

hurricanes, earthquakes, tornadoes, discoloration due 

to over-heating, exposure to chemicals (including salt), 

either directly or in the atmosphere, or very high 

humidity, is not covered by this Limited Warranty.

There are no other express warranties except as set 

forth herein. For consumer applications, any 

applicable implied warranties of merchantability and 

fitness are limited in duration to the period of coverage 

of this Limited Warranty. Some states do not allow 

limitation on how long an implied warranty lasts, so this 

limitation may not apply to you.

For Commercial applications, the liability of 

Firegear Outdoors is limited to the express terms of this 

warranty. We expressly disclaim any and all implied 

warranties, including any warranties of fitness for a 

particular purpose or merchantability.

We are not liable for any special, indirect or 

consequential damages. Our maximum liability is 

limited to the purchase price of the purchased products. 

Some states do not allow the exclusion or limitation of 

incidental or consequential damages, so this limitation or 

exclusions may not apply to you.

We do not authorize any person or company to 

assume for it any other obligation or liability in 

connection with the sale, installation, use, removal, 

return, or replacement of its equipment; and no such 

representations are binding. 

REV. 3-2-16

LIMITED WARRANTY

Summary of Contents for ANF-L48















Reviews: